REAR DOOR WINDOW FRAME MOULDING INSTALLATION

PROCEDURE

1. INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

   
   

   1. 

      Engage the guide and 2 claws, and install the rear door window frame moulding sub-assembly to the door frame.

   2. Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 7 new rivets.

      Tech Tips

      If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

      Note

      
      

      • 

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

        Text in Illustration

        *1	Riveter
        *2	Mandrel
        *a	Incorrect

      • 

        Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

        Text in Illustration

        *1	Riveter
        *a	Incorrect

      • 

        Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

        Text in Illustration

        *1	Riveter
        *a	Incorrect

2. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

   Tech Tips

   When installing a new rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

   Heating Temperature

   Item	Temperature
   Vehicle Body	40 to 60°C (104 to 140°F)
   Moulding	20 to 30°C (68 to 86°F)

   Note

   Do not heat the vehicle body or rear door front window frame moulding excessively.

   
   

   1. Clean the vehicle body surface.

      
      

      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

   2. 

      Text in Illustration

      *1	Double-sided Tape
      *2	Caulking Sponge

      Install a new rear door front window frame moulding.

      
      

      1. Using a heat light, heat the vehicle body and rear door front window frame moulding.

      2. Remove the release paper from the rear door front window frame moulding.

         Tech Tips

         After removing the release paper, keep the exposed adhesive free from foreign matter.

      3. Install the rear door front window frame moulding with the clip.

3. INSTALL REAR DOOR BELT MOULDING ASSEMBLY

   Click here

4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

   Click here

5. INSTALL REAR DOOR QUARTER WINDOW GLASS

   Click here

6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

   Click here

7. INSTALL NO. 1 REAR DOOR VENT SEAL

   Click here

8. INSTALL REAR DOOR GLASS RUN

   Click here

9. INSTALL REAR DOOR WEATHERSTRIP

   Click here

10. INSTALL REAR DOOR CHECK ASSEMBLY

    Click here

11. INSTALL REAR DOOR SERVICE HOLE COVER

    Click here

12. INSTALL REAR DOOR TRIM BRACKET

    Click here

13. INSTALL REAR DOOR SPEAKER COVER (w/o Rear Speaker)

    Click here

14. INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

    Click here

15. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

    Click here

16. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

17. INSTALL REAR DOOR ARMREST COVER

    Click here

18. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

19. INSTALL REAR DOOR REAR FRAME BRACKET

    Click here

20. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

22. INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE

    Click here

23. INSTALL DECK FLOOR BOX RH

    Click here

24. INSTALL REAR NO. 3 FLOOR BOARD

    Click here

25. INSTALL REAR DECK FLOOR BOX

    Click here

26. INSTALL REAR NO. 2 FLOOR BOARD

    Click here

27. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here