FRONT DOOR WINDOW FRAME MOULDING INSTALLATION

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work Click here.

  2. INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING


    1. B001LOW

      Engage the front door upper window frame moulding to the door frame.

    2. Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 8 new rivets.

      Tech Tips

      If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

      Note


      • B001LFUE09

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

        Text in Illustration
        *1 Riveter
        *2 Mandrel
        *a Incorrect
      • B001LG0E10

        Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

        Text in Illustration
        *1 Riveter
        *a Incorrect
      • B001LODE12

        Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

        Text in Illustration
        *1 Riveter
        *a Incorrect

  3. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

    Tech Tips

    When installing a new front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or front door rear window frame moulding excessively.


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

    2. B001MNAE01
      Text in Illustration
      *1 Double-sided Tape
      *2 Caulking Sponge

      Install a new front door rear window frame moulding.


      1. Using a heat light, heat the vehicle body and front door rear window frame moulding.

      2. Remove the release paper from the face of the front door rear window frame moulding.

        Tech Tips

        After removing the release paper, keep the exposed adhesive free from foreign matter.

      3. Install the front door rear window frame moulding with the clip.

  4. INSTALL FRONT DOOR WEATHERSTRIP

    Click here

  5. INSTALL FRONT DOOR CHECK ASSEMBLY

    Click here

  6. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

    Click here

  7. INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER

    Click here

  8. INSTALL FRONT DOOR GLASS RUN

    Click here

  9. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  10. INSTALL FRONT DOOR SERVICE HOLE COVER

    Click here

  11. INSTALL FRONT DOOR TRIM BRACKET (for Driver Side)

    Click here

  12. INSTALL FRONT DOOR TRIM BRACKET (for Front Passenger Side)

    Click here

  13. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Driver Side)

    Click here

  14. INSTALL DOOR ARMREST COVER (for Driver Side)

    Click here

  15. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    Click here

  16. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Passenger Side)

    Click here

  17. INSTALL DOOR ASSIST GRIP ASSEMBLY (for Front Passenger Side)

    Click here

  18. INSTALL DOOR ASSIST GRIP COVER (for Front Passenger Side)

    Click here

  19. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Click here

  20. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

    Click here

  21. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  23. INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE

    Click here

  24. INSTALL DECK FLOOR BOX RH

    Click here

  25. INSTALL REAR NO. 3 FLOOR BOARD

    Click here

  26. INSTALL REAR DECK FLOOR BOX

    Click here

  27. INSTALL REAR NO. 2 FLOOR BOARD

    Click here

  28. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here