PRE-COLLISION SYSTEM, Diagnostic DTC:C1A47

DTC Code DTC Name
C1A47 Steering Angle Sensor

DESCRIPTION

The driving support ECU assembly receives steering angle information from the steering sensor (spiral cable with sensor sub-assembly). If the driving support ECU assembly detects a steering sensor (spiral cable with sensor sub-assembly) malfunction, DTC C1A47 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A47 Steering Angle Sensor While the vehicle is being driven at a speed of 50 km/h (32 mph) or more, the driving support ECU assembly receives a steering sensor (spiral cable with sensor sub-assembly) malfunction signal continuously for 1 second or more.

  • Electronically controlled brake system

  • Skid control ECU (Brake booster with master cylinder assembly)

  • Driving support ECU assembly

CAUTION / NOTICE / HINT

Note


  • When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

  • The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here

PROCEDURE


  1. CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

    Tech Tips

    Pre-collision system DTC C1A47 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

    5. Check for DTCs.

      Click here

      Result
      Result Proceed to
      Electronically controlled brake system DTCs are not output A
      Electronically controlled brake system DTCs are output B

    B

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM Click here

    A

  2. CHECK FOR DTCs (PRE-COLLISION SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.

    5. Clear the DTCs.

      Click here

    6. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.

    7. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC C1A47 is not output A
      DTC C1A47 is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

  3. REPLACE DRIVING SUPPORT ECU ASSEMBLY


    1. Replace the driving support ECU assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK FOR DTCs (PRE-COLLISION SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.

    5. Clear the DTCs.

      Click here

    6. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Drive the vehicle at a speed of 50 km/h (32 mph) or more for 1 second or more.

    7. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC C1A47 is not output A
      DTC C1A47 is output B

    A

    END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

    B

    REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) for LHD: Click here for RHD: Click here