PRE-CRASH SAFETY SYSTEM, Diagnostic DTC:U0122, U0123, U0126, U0140, U0151, U0293, U1002, U1100, U1104

DTC Code	DTC Name
U0122	Lost Communication with Vehicle Dynamics Control Module
U0123	Lost Communication with Yaw Rate Sensor Module
U0126	Lost Communication with Steering Angle Sensor Module
U0140	Lost Communication with Main Body ECU
U0151	Lost Communication with Airbag ECU
U0293	Lost Communication with HV ECU
U1002	Lost Communication with Gateway Module
U1100	Lost Communication with Seat Belt Control ECU
U1104	Lost Communication with Driving Support ECU

DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle. Based on this information, the driving support ECU assembly sends pre-crash control operation signals. These DTCs are stored when a communication malfunction occurs between the sensors and ECUs that detect crashes, or between ECUs that perform the pre-crash control.

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects ahead to the driving support ECU assembly. The driving support ECU assembly sends this information to the seat belt control ECU and performs pre-crash system (DTC U1104).

DTC No.	DTC Detection Condition	Trouble Area
U0122	When the power switch is on (IG), a communication error between the brake booster with master cylinder (skid control ECU) and the driving support ECU assembly is detected for approx. 3 seconds. When the power switch is on (IG), a communication error between the brake booster with master cylinder (skid control ECU) and the seat belt control ECU is detected for approx. 3 seconds.	Brake booster with master cylinder (skid control ECU) CAN communication system Driving support ECU assembly Wire harness or connector Seat belt control ECU
U0123	When the power switch is on (IG), a communication error between the yaw rate sensor assembly and the driving support ECU assembly is detected for approx. 1 second.	Yaw rate sensor assembly CAN communication system Driving support ECU assembly
U0126	When the power switch is on (IG), a communication error between the steering angle sensor and the driving support ECU assembly is detected for approx. 4 seconds.	Steering angle sensor CAN communication system Driving support ECU assembly
U0140	When the power switch is on (IG), communication stop between the main body ECU and seat belt control ECU continues for 6 seconds or more.	Main body ECU CAN communication system Seat belt control ECU Wire harness or connector
U0151	When the power switch is on (IG), communication stop between the center airbag sensor and seat belt control ECU continues for 6 seconds or more.	Center airbag sensor CAN communication system Seat belt control ECU Wire harness or connector
U0293	When the power switch is on (IG), a communication error between the power management control ECU and brake booster with master cylinder (skid control ECU) is detected for approx. 1 second. When the power switch is on (IG), a communication error between the power management control ECU and driving support ECU assembly is detected for approx. 4 seconds.	Power management control ECU Brake booster with master cylinder (skid control ECU) CAN communication system Driving support ECU assembly
U1002	When the power switch is on (IG), communication stop between the millimeter wave radar sensor assembly and driving support ECU assembly continues for 1 second or more.	Millimeter wave radar sensor assembly CAN communication system Driving support ECU assembly
U1100	When the power switch is on (IG), a communication error between the seat belt control ECU and the driving support ECU assembly is detected for approx. 9 seconds.	Seat belt control ECU CAN communication system Driving support ECU assembly
U1104	When the power switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approx. 1 second. When the power switch is on (IG), a communication error between the driving support ECU assembly and the power management control ECU is detected for approx. 1 second. When the power switch is on (IG), a communication error between the driving support ECU assembly and seat belt control ECU is detected for approx. 1 second.	Communication circuit millimeter wave radar sensor assembly Driving support ECU assembly CAN communication system Wire harness or connector

WIRING DIAGRAM

CAUTION / NOTICE / HINT

Note

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed Click here.
Confirm that the connector is securely connected, as a partially connected connector is suspected for the cause of this DTC.

PROCEDURE

CHECK DTC OUTPUT

Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Pre-Crash and Pre-Crash 2 / DTC.

Check for DTCs.

Result

Result	Proceed to
DTC U1104 is output	A
DTCs other than U1104 are output	B

GO TO CAN COMMUNICATION SYSTEM Click here

CHECK CAN COMMUNICATION SYSTEM
1. Using the intelligent tester to check if the CAN communication system is functioning normally Click here.
  
  OK
  
  CAN communication system DTC is not output.
NG
GO TO CAN COMMUNICATION SYSTEM Click here

OK

OK
CAN communication system DTC is not output.

CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)

Text in Illustration

*a
Front view of wire harness connector

(to Millimeter Wave Radar Sensor Assembly)

Disconnect the millimeter wave radar sensor assembly connector.
Turn the power switch on (IG).

Text in Illustration
*a	Front view of wire harness connector (to Millimeter Wave Radar Sensor Assembly)

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Condition	Specified Condition
A2-5 (IGB) - Body ground	Power switch on (IG)	11 to 14 V

Reconnect the millimeter wave radar sensor assembly connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR

CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

Text in Illustration

*a
Front view of wire harness connector

(to Millimeter Wave Radar Sensor Assembly)

Disconnect the millimeter wave radar sensor assembly connector.

Text in Illustration
*a	Front view of wire harness connector (to Millimeter Wave Radar Sensor Assembly)

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
A2-2 (SGND) - Body ground	Always	Below 1 Ω

Reconnect the millimeter wave radar sensor assembly connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
1. Replace the millimeter wave radar sensor assembly Click here.
2. Adjust the millimeter wave radar sensor assembly Click here.
NEXT

CHECK DTC OUTPUT

Clear the DTCs Click here.
Turn the power switch on (IG).

Check if the same DTC is output Click here.

Result

Result	Proceed to
DTC U1104 is not output	A
DTC U1104 is output	B

END

REPLACE DRIVING SUPPORT ECU ASSEMBLY Click here