SEAT POSITION SENSOR INSTALLATION

CAUTION / NOTICE / HINT

Note


  • Use the same procedure for the driver side of RHD and LHD vehicles.

  • The procedures listed below are for the driver side of an LHD vehicle.

PROCEDURE


  1. INSTALL SEAT POSITION AIRBAG SENSOR (for Manual Seat)


    1. A004VZ6

      Install the seat position airbag sensor to the seat slide position sensor protector with the pin as shown in the illustration.

    2. A004YZRE02
      Text in Illustration
      *1 Seat Position Airbag Sensor
      *2 Feeler Gauge
      *3 Seat Rail

      Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position airbag sensor with the "TORX" screw.

      Note


      • If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.

      • When installing the seat position airbag sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    3. Using a T30 "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Make sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    5. Connect the connector.

    6. Install the wire harness to the 2 hooks.

    7. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  2. INSTALL SEAT POSITION AIRBAG SENSOR (for Power Seat)


    1. A004VZ6

      Install the seat position airbag sensor to the seat slide position sensor protector with the pin as shown in the illustration.

    2. A004YZRE02
      Text in Illustration
      *1 Seat Position Airbag Sensor
      *2 Feeler Gauge
      *3 Seat Rail

      Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position airbag sensor with the "TORX" screw and nut.

      Note


      • If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.

      • When installing the seat position airbag sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    3. Using a T30 "TORX" socket wrench, install the seat position airbag sensor with the "TORX" screw and nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Make sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    5. Connect the connector.

    6. Install the wire harness to the 2 hooks.

    7. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  3. INSTALL FRONT SEAT CUSHION SHIELD LH (for Manual Seat)

    Click here

  4. INSTALL VERTICAL ADJUSTING HANDLE LH (for 6 Way Seat Type)

    Click here

  5. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)

    Click here

  6. INSTALL FRONT SEAT ASSEMBLY LH

    for Manual Seat: Click here

    for Power Seat: Click here

  7. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here