SPIRAL CABLE INSPECTION

PROCEDURE


  1. INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Visually check for defects with the spiral cable with sensor sub-assembly removed from the vehicle.


      1. The defects are as follows:


        • Scratches on the spiral cable with sensor sub-assembly

        • Small cracks on the spiral cable with sensor sub-assembly

        • Dents on the spiral cable with sensor sub-assembly

        • Chips on the spiral cable with sensor sub-assembly

        • Cracks or other damage to the connector

          OK
          No defects are found.

        Tech Tips

        If any of the defects is found, replace the spiral cable with sensor sub-assembly with a new one.

    2. Check the spiral cable with sensor sub-assembly.

      A004WM8E01
      Text in Illustration
      *1 Color: Orange
      *2 Color: Black
      *a

      Component without harness connected

      (Spiral Cable with Sensor Sub-assembly)

      1. Set the spiral cable with sensor sub-assembly to the center position.

      2. Measure the resistance between each terminal of the spiral cable with sensor sub-assembly according to the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        H30-1 (CCS) - z5-3 Always Below 1 Ω
        H30-2 (ECC) - z5-4 Always Below 1 Ω
        H30-2 (ECC) - z4-7 Always Below 1 Ω
        H30-3 (EAU) - z4-8 Always Below 1 Ω
        H30-5 (AU2) - z4-10 Always Below 1 Ω
        H30-6 (AU1) - z4-11 Always Below 1 Ω
        H30-8 (R/N) - z5-1 Always Below 1 Ω
        H30-9 (HO) - z4-1 Always Below 1 Ω
        H30-10 (+DP) - z4-2 Always Below 1 Ω
        H30-11 (-DP) - z4-3 Always Below 1 Ω
        H30-12 (DIST) - z4-4 Always Below 1 Ω
        H30-13 (IL+2) - z4-5 Always Below 1 Ω
        H31-1 (D+) - z2-2 (D+) Always Below 1 Ω
        H31-2 (D-) - z2-1 (D-) Always Below 1 Ω
        H31-3 (D2-) - z3-1 (D2-) Always Below 1 Ω
        H31-4 (D2+) - z3-2 (D2+) Always Below 1 Ω

      3. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable with sensor sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        H30-1 (CCS) - z5-3 Always Below 1 Ω
        H30-2 (ECC) - z5-4 Always Below 1 Ω
        H30-2 (ECC) - z4-7 Always Below 1 Ω
        H30-3 (EAU) - z4-8 Always Below 1 Ω
        H30-5 (AU2) - z4-10 Always Below 1 Ω
        H30-6 (AU1) - z4-11 Always Below 1 Ω
        H30-8 (R/N) - z5-1 Always Below 1 Ω
        H30-9 (HO) - z4-1 Always Below 1 Ω
        H30-10 (+DP) - z4-2 Always Below 1 Ω
        H30-11 (-DP) - z4-3 Always Below 1 Ω
        H30-12 (DIST) - z4-4 Always Below 1 Ω
        H30-13 (IL+2) - z4-5 Always Below 1 Ω
        H31-1 (D+) - z2-2 (D+) Always Below 1 Ω
        H31-2 (D-) - z2-1 (D-) Always Below 1 Ω
        H31-3 (D2-) - z3-1 (D2-) Always Below 1 Ω
        H31-4 (D2+) - z3-2 (D2+) Always Below 1 Ω

      4. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        H30-1 (CCS) - z5-3 Always Below 1 Ω
        H30-2 (ECC) - z5-4 Always Below 1 Ω
        H30-2 (ECC) - z4-7 Always Below 1 Ω
        H30-3 (EAU) - z4-8 Always Below 1 Ω
        H30-5 (AU2) - z4-10 Always Below 1 Ω
        H30-6 (AU1) - z4-11 Always Below 1 Ω
        H30-8 (R/N) - z5-1 Always Below 1 Ω
        H30-9 (HO) - z4-1 Always Below 1 Ω
        H30-10 (+DP) - z4-2 Always Below 1 Ω
        H30-11 (-DP) - z4-3 Always Below 1 Ω
        H30-12 (DIST) - z4-4 Always Below 1 Ω
        H30-13 (IL+2) - z4-5 Always Below 1 Ω
        H31-1 (D+) - z2-2 (D+) Always Below 1 Ω
        H31-2 (D-) - z2-1 (D-) Always Below 1 Ω
        H31-3 (D2-) - z3-1 (D2-) Always Below 1 Ω
        H31-4 (D2+) - z3-2 (D2+) Always Below 1 Ω

        If the result is not as specified, replace the spiral cable with sensor sub-assembly.

        Note

        As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.