LIGHTING SYSTEM OPERATION CHECK


  1. INSPECT INTERIOR LIGHT CONTROL OPERATION

    Note

    Perform this inspection with the customize parameters at the initial settings.

    Tech Tips

    The interior light control illuminates the lights below.


    • Power Switch Illumination

    • Map Light Assembly

    • No. 1 Room Light Assembly


    1. The operation and conditions of this control are described below.

      Operation Condition
      Fade in and illuminate constantly Any door is opened when all doors are closed.
      Illuminate for 15 seconds, and then fade out

      When any of the following conditions is met, the lights illuminate for 15 seconds, and then fade out:


      • The key enters any actuation area around the doors when the power switch is off and all doors are closed*1.

      • Any door is unlocked when the power switch is off with all doors closed and locked.

      • The power switch is turned from on (IG) to off when all doors are closed.

      • All doors are closed after any door is opened and the power switch is off.
      Fade out immediately

      When any of the following conditions is met, the lights fade out immediately:


      • The power switch is turned from off to on (ACC) when all doors are closed.

      • All doors are locked when the power switch is off, all doors are closed and any door is unlocked.

      • All doors are locked again when all doors are already closed and locked.
      Battery saving When no changes occur in the condition of the doors for 20 minutes and a key is not in the actuation area, the lights that operate turn off.

      Tech Tips

      *1: When the lights are on, if the key leaves all of actuation areas around the doors, after approximately 3 seconds, the lights fade out.

  2. INSPECT FOOTWELL LIGHT CONTROL OPERATION

    Note

    Perform this inspection with the customize parameters at the initial settings.

    Tech Tips

    The footwell light control illuminates the lights below.


    • No. 1 Interior Illumination Light Assembly LH

    • No. 1 Interior Illumination Light Assembly RH


    1. The operation and conditions of this control are described below.

      Operation Condition
      Fade in and illuminate constantly

      When either of the following conditions is met, the footwell light LH and footwell light RH fade in:


      • Any door is opened when all doors are closed.

      • The power switch is turned from off to on (IG).
      Illuminate for 15 seconds, and then fade out

      When any of the following conditions is met, the footwell light LH and foot light RH illuminate for 15 seconds and then fade out:


      • Any door is unlocked when the power switch is off, all doors are closed and all doors are locked.

      • The power switch is turned from on (IG) to off when all doors are closed.

      • All doors are closed when any door is opened and the power switch is off.
      Fade out immediately All doors are locked when the power switch is off, all doors are closed and any door is unlocked.

  3. INSPECT CENTER CONSOLE SPOT LIGHT CONTROL OPERATION

    Note

    Perform this inspection with the customize parameters at the initial settings.

    Tech Tips

    The center console spot light control illuminates the light below.


    • Center Console Spot Light


    1. The operation and conditions of this control are described below.

      Operation Condition
      Fade in

      When either of the following conditions is met, the center console spot light fades in.


      • The power switch is on (ACC).

      • The power switch is on (IG).
      Fade out The power switch is off.

  4. BATTERY SAVING CONTROL OPERATION

    Note

    Perform this inspection with the customize parameters at the initial settings.

    Tech Tips

    The lights controlled by battery saving control are as follows:


    • Map Light Assembly

    • No. 1 Room Light Assembly

    • Vanity Light Assembly LH and RH

    • No. 2 Room Light Assembly


    1. The operation and conditions of this control are described below.

      Operation Condition
      Battery saving

      When 20 minutes elapse after the power switch is turned from on (ACC) or on (IG) to off and the lights that operate remain on, the lights are turned off.

      Tech Tips

      Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then are turned off.


      • The power switch is turned on (ACC) or on (IG)

      • Any door is opened and closed

      • The back door is opened and closed

      • Any door is unlocked

      • The key enters any exterior actuation area