ENTRY AND START SYSTEM(for Entry Function), Diagnostic DTC:B27A1

DTC Code DTC Name
B27A1 Open in Driver Side Electrical Antenna Circuit

DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) [electrical key antenna] at intervals of 250 ms. For the front door outside handle assembly (for driver door) [electrical key antenna] to detect when the key is brought close to the vehicle, a signal requesting a response from the key is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 250 ms. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [electrical key antenna] (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A1 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).

  • Harness or connector

  • Front door outside handle assembly (for driver door)

  • Certification ECU (smart key ECU assembly)

 Any time

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for driver door -
Related Data List and Active Test
DTC Code Data List and Active Test
B27A1 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B001NC3E46

CAUTION / NOTICE / HINT

Note


  • The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

  • When using the intelligent tester with the power switch off to troubleshoot:

    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) Click here.

  • After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

  • Front door outside handle assembly (for driver door) has an antenna coil between ANT1 and ANT2 terminals.

PROCEDURE


  1. CHECK CONNECTOR CONNECTION


    1. Turn the power switch off.

    2. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).

      OK
      Connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)


    1. Disconnect the H1 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the O1*1, N1*2 front door outside handle assembly (for driver door) connector.

    3. Measure the resistance according to the value(s) in the table below.


      • *1: for LHD

      • *2: for RHD

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      H1-3 (CLG1) - O1-6 (ANT1) Always Below 1 Ω
      H1-4 (CG1B) - O1-3 (ANT2) Always Below 1 Ω
      H1-15 (E) - Body ground Always Below 1 Ω
      O1-2 (GND) - Body ground Always Below 1 Ω
      H1-3 (CLG1) or O1-6 (ANT1) - Body ground Always 10 kΩ or higher
      H1-4 (CG1B) or O1-3 (ANT2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      H1-3 (CLG1) - N1-6 (ANT1) Always Below 1 Ω
      H1-4 (CG1B) - N1-3 (ANT2) Always Below 1 Ω
      H1-15 (E) - Body ground Always Below 1 Ω
      N1-2 (GND) - Body ground Always Below 1 Ω
      H1-3 (CLG1) or N1-6 (ANT1) - Body ground Always 10 kΩ or higher
      H1-4 (CG1B) or N1-3 (ANT2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)


    1. Connect the H1 certification ECU (smart key ECU assembly) connector.

      B001MR0E03
      Text in Illustration
      *1 Waveform 1 *2 Waveform 2
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      		 - -

    2. Connect the O1*1, N1*2 front door outside handle assembly (for driver door) connector.

    3. Using an oscilloscope, check the waveform.

      OK
      Tester Connection Switch Condition Tool Setting Specified Condition
      H1-3 (CLG1) - H1-15 (E)

      Procedure:


      1. Power switch off

      2. Key brought outside vehicle

      3. All doors closed

      4. Key not inside vehicle

      5. Key brought inside detection area*3

      6. All doors locked through wireless operation

      		 2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
      H1-3 (CLG1) - H1-15 (E)

      Procedure:


      1. Power switch off

      2. Key brought outside vehicle

      3. All doors closed

      4. Key not inside vehicle

      5. Key brought outside detection area*4

      6. All doors locked through wireless operation

      		 2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)
      H1-4 (CG1B) - H1-15 (E)

      Procedure:


      1. Power switch off

      2. Key brought outside vehicle

      3. All doors closed

      4. Key not inside vehicle

      5. Key brought outside detection area*4

      6. All doors locked with key

      		 2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)

      • *1: for LHD

      • *2: for RHD

      • *3: For details about the areas that are inside the entry function detection area, refer to Operation Check Click here.

      • *4: For details about the areas that are outside the entry function detection area, refer to Operation Check Click here.


    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

  4. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)


    1. Temporarily replace the front door outside handle assembly (for driver door) with a new or normally functioning one Click here.


    NEXT

  5. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  6. CHECK FOR DTC


    1. Check for DTCs Click here.

      OK
      DTC B27A1 is not output.

    OK

    END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)