REAR DOOR LOCK REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After the power switch is turned off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 2 FLOOR BOARD

    Click here

  3. REMOVE REAR DECK FLOOR BOX

    Click here

  4. REMOVE REAR NO. 3 FLOOR BOARD

    Click here

  5. REMOVE DECK FLOOR BOX RH

    Click here

  6. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE

    Click here

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  9. REMOVE REAR DOOR REAR FRAME BRACKET

    Click here

  10. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

  11. REMOVE REAR DOOR ARMREST COVER

    Click here

  12. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  13. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

    Click here

  14. REMOVE REAR DOOR TRIM BRACKET

    Click here

  15. REMOVE REAR DOOR SERVICE HOLE COVER

    Click here

  16. REMOVE REAR DOOR CHECK ASSEMBLY

    Click here

  17. REMOVE REAR DOOR WEATHERSTRIP

    Click here

  18. REMOVE REAR DOOR GLASS RUN

    Click here

  19. REMOVE NO. 1 REAR DOOR VENT SEAL

    Click here

  20. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

    Click here

  21. REMOVE REAR DOOR QUARTER WINDOW GLASS

    Click here

  22. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  23. REMOVE REAR DOOR LOCK ASSEMBLY (w/o Double Locking System)


    1. B001MAD

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. B001MKO

      Remove the door lock wiring harness seal from the rear door lock assembly.

    4. B001K8T

      Using a screwdriver, disengage the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    5. B001MR3

      Remove the rear door lock remote control cable assembly.

    6. B001MPR

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    7. B001MIM

      Remove the rear door inside locking cable assembly.

  24. REMOVE REAR DOOR LOCK ASSEMBLY (w/ Double Locking System)


    1. B001MAD

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. B001MKO

      Remove the door lock wiring harness seal from the rear door lock assembly.

    4. B001M2M

      Using a screwdriver, disengage the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    5. B001KFD

      Remove the rear door lock remote control cable assembly.

    6. B001KYA

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    7. B001LW7

      Remove the rear door inside locking cable assembly.