CAN COMMUNICATION SYSTEM Central Gateway ECU Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
Central Gateway ECU Communication Stop Mode Communication system DTCs (DTCs that start with U) that correspond to "Central Gateway ECU Communication Stop Mode" in "DTC Combination Table" are output.

  • Central gateway ECU (network gateway ECU) main line or connector

  • Central gateway ECU (network gateway ECU) branch line or connector

  • Power source circuit of central gateway ECU (network gateway ECU)

  • Central gateway ECU (network gateway ECU) ground circuit

  • Central gateway ECU (network gateway ECU)

WIRING DIAGRAM

B001LAHE04
B001LERE04
B001KO9E06

CAUTION / NOTICE / HINT

Note


  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE


  1. CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) MAIN LINE AND BRANCH LINE)


    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    2. Disconnect the H188 central gateway ECU (network gateway ECU) connector.

    3. B001NEQC20
      *a

      Front view of wire harness connector

      (to Central Gateway ECU (Network Gateway ECU))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Bus 2 Branch Lines
      Tester Connection Condition Specified Condition
      H188-18 (CA4H) - H188-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
      Bus 3 Main Lines
      Tester Connection Condition Specified Condition
      H188-6 (CA3H) - H188-19 (CAYH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
      H188-21 (CA3L) - H188-20 (CAYL)
      Bus 5 Main Lines
      Tester Connection Condition Specified Condition
      H188-15 (CA5H) - H188-16 (CA5L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
      Result
      Result Proceed to
      OK A
      NG (Bus 2 branch lines) B
      NG (Bus 3 main lines) C
      NG (Bus 5 main lines) D

    B

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

    C

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

    D

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

    A

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. B001LE1C68
      *a

      Front view of wire harness connector

      (to Central Gateway ECU (Network Gateway ECU))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H188-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω

    2. Reconnect the cable to the negative (-) auxiliary battery terminal.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H188-1 (BATT) - Body ground power switch off 11 to 14 V
      H188-2 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
      H188-11 (IG1) - Body ground Power switch on (IG) 11 to 14 V
      H188-12 (IG2) - Body ground Power switch on (IG) 11 to 14 V
      Result
      Result
      OK
      NG

    OK

    REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)