REAR VIEW MONITOR SYSTEM(for Inner Rear View Mirror Type) Image from Camera for Rear View Monitor is Abnormal

DESCRIPTION

The video signal of the rear television camera assembly is transmitted to the inner rear view mirror assembly.

WIRING DIAGRAM

B001KHQE06

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (INNER REAR VIEW MIRROR ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)


    1. Disconnect the T9 inner rear view mirror assembly connector.

    2. Disconnect the V14 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T9-7 (CV+) - V14-3 (CV+) Always Below 1 Ω
      T9-14 (CB+) - V14-6 (CB+) Always Below 1 Ω
      T9-6 (CV-) - V14-2 (CV-) Always Below 1 Ω
      T9-13 (CGND) - V14-5 (CGND) Always Below 1 Ω
      T9-7 (CV+) - Body ground Always 10 kΩ or higher
      T9-14 (CB+) - Body ground Always 10 kΩ or higher
      T9-6 (CV-) - Body ground Always 10 kΩ or higher
      T9-13 (CGND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT INNER REAR VIEW MIRROR ASSEMBLY


    1. B001LOBE02
      Text in Illustration
      *a

      Component with harness connected

      (Inner Rear View Mirror Assembly)

      Reconnect the T9 inner rear view mirror assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T9-6 (CV-) - Body ground Always Below 1 Ω
      T9-13 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      T9-14 (CB+) - T9-13 (CGND)

      Power switch on (READY)

      Reverse (R) selected

      		 5.5 to 7.05 V

    NG

    REPLACE INNER REAR VIEW MIRROR ASSEMBLY Click here

    OK

  3. INSPECT REAR TELEVISION CAMERA ASSEMBLY


    1. B001KHFE01
      Text in Illustration
      *a

      Component with harness connected

      (Inner Rear View Mirror Assembly)

      Reconnect the V14 rear television camera assembly connector.

    2. B001KO5E01
      Text in Illustration
      *a Waveform 1 (camera lens is not covered, displaying an image)
      *b Waveform 2 (camera lens is covered, blacking out the screen)
      *c Synchronization Signal
      *d Video Waveform

      Using an oscilloscope, check the waveform of the rear television camera assembly.

      Tech Tips

      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the inner rear view mirror assembly with the connector connected.

      OK
      Waveform is similar to that shown in the illustration.
      Item Content
      Measurement terminal T9-7 (CV+) - T9-2 (E)
      Measurement setting 200 mV/DIV., 50 μs./DIV.
      Condition Power switch on (READY), reverse (R) selected

      Tech Tips

      The video waveform changes according to the image sent by the rear television camera assembly.


    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here