PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function), Diagnostic DTC:C1622

DTC Code DTC Name
C1622 Back Camera Disconnected

DESCRIPTION

This DTC is stored if the radio receiver assembly judges that the signals or signal lines between the radio receiver assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. DTC Detection Condition Trouble Area
C1622 Open or short in the rear television camera assembly signal circuit

  • Harness or connector

  • Rear television camera assembly

  • Radio receiver assembly

WIRING DIAGRAM

B001MX7E15

CAUTION / NOTICE / HINT

Note


  • When "System initializing" is displayed on the multi-display after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)


    1. Disconnect the H147 radio receiver assembly connector.

    2. Disconnect the V14 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H147-39 (CA+) - V14-6 (CB+) Always Below 1 Ω
      H147-18 (V+) - V14-3 (CV+) Always Below 1 Ω
      H147-19 (V-) - V14-2 (CV-) Always Below 1 Ω
      H147-40 (CGND) - V14-5 (CGND) Always Below 1 Ω
      H147-39 (CA+) - Body ground Always 10 kΩ or higher
      H147-18 (V+) - Body ground Always 10 kΩ or higher
      H147-19 (V-) - Body ground Always 10 kΩ or higher
      H147-40 (CGND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT RADIO RECEIVER ASSEMBLY (CA+, V-, CGND)


    1. Reconnect the H147 radio receiver assembly connector.

    2. B001KM5E02
      Text in Illustration
      *a

      Component with harness connected

      (Radio Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H147-19 (V-) - Body ground Always Below 1 Ω
      H147-40 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H147-39 (CA+) - H147-40 (CGND) Power switch on (ACC) 5.5 to 7.05 V

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    OK

  3. INSPECT RADIO RECEIVER ASSEMBLY (V+, GND1)


    1. Reconnect the V14 rear television camera assembly connector.

    2. B001MKZE02
      Text in Illustration
      *a

      Component with harness connected

      (Radio Receiver Assembly)
      B001KO5E01
      Text in Illustration
      *a Waveform 1 (camera lens is not covered, displaying an image)
      *b Waveform 2 (camera lens is covered, blacking out the screen)
      *c Synchronization Signal
      *d Video Waveform

      Using an oscilloscope, check the waveform of the rear television camera assembly.

      Tech Tips

      A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio receiver assembly with the connector connected.

      OK
      Waveform is similar to that shown in the illustration.
      Item Content
      Measurement terminal H147-18 (V+) - H147-12 (GND1)
      Measurement setting 200 mV/DIV., 50 μs./DIV.
      Condition Power switch on (IG), reverse (R) selected

      Tech Tips


      • The video waveform changes according to the image sent by the rear television camera assembly.

      • The video waveform is constantly output when the power switch is on (ACC).


    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here