HYBRID TRANSAXLE OIL SEAL REPLACEMENT

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE FRONT WHEEL

  2. REMOVE REAR ENGINE UNDER COVER LH (for 2ZR-FXE)

    Click here

  3. REMOVE REAR ENGINE UNDER COVER LH (for 5ZR-FXE)

    Click here

  4. REMOVE REAR ENGINE UNDER COVER RH (for 2ZR-FXE)

    Click here

  5. REMOVE REAR ENGINE UNDER COVER RH (for 5ZR-FXE)

    Click here

  6. REMOVE NO. 1 ENGINE UNDER COVER (for 2ZR-FXE)

    Click here

  7. REMOVE NO. 1 ENGINE UNDER COVER (for 5ZR-FXE)

    Click here

  8. DRAIN HYBRID TRANSAXLE FLUID

    Click here

  9. REMOVE FRONT AXLE SHAFT NUT

    Click here

  10. SEPARATE TIE ROD END SUB-ASSEMBLY

    Click here

  11. SEPARATE FRONT SPEED SENSOR

    Click here

  12. SEPARATE FRONT FLEXIBLE HOSE

    Click here

  13. SEPARATE FRONT STABILIZER LINK ASSEMBLY

    Click here

  14. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

    Click here

  15. SEPARATE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  16. REMOVE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  17. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

    Click here

  18. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL


    1. B001MJWE05
      Text in Illustration
      *a LH Side
      *b RH Side

      Using SST, remove the 2 oil seals.

      SST
      09308-00010

  19. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL


    1. Install a new LH side oil seal.


      1. B001N58E03

        Using SST and a hammer, tap in a new oil seal.

        SST
        09316-10010
        09950-70010   ( 09951-07150 )
        Oil seal installation depth
        -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      2. Coat the lip of the oil seal with MP grease.

    2. Install a new RH side oil seal.


      1. B001LX6E03

        Using SST and a hammer, tap in a new oil seal.

        SST
        09726-36010
        09950-70010   ( 09951-07150 )
        Oil seal installation depth
        -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      2. Coat the lip of the oil seal with MP grease.

  20. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

    Click here

  21. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  22. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

    Click here

  23. INSTALL FRONT STABILIZER LINK ASSEMBLY

    Click here

  24. INSTALL FRONT FLEXIBLE HOSE

    Click here

  25. INSTALL FRONT SPEED SENSOR

    Click here

  26. CONNECT TIE ROD END SUB-ASSEMBLY

    Click here

  27. INSTALL FRONT AXLE SHAFT NUT

    Click here

  28. ADD HYBRID TRANSAXLE FLUID

    Click here

  29. INSPECT HYBRID TRANSAXLE FLUID

    Click here

  30. INSPECT FOR TRANSAXLE FLUID LEAK

  31. INSTALL FRONT WHEEL (for 2ZR-FXE)

    Click here

  32. INSTALL FRONT WHEEL (for 5ZR-FXE)

    Click here

  33. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  34. INSTALL NO. 1 ENGINE UNDER COVER (for 2ZR-FXE)

    Click here

  35. INSTALL NO. 1 ENGINE UNDER COVER (for 5ZR-FXE)

    Click here

  36. INSTALL REAR ENGINE UNDER COVER LH (for 2ZR-FXE)

    Click here

  37. INSTALL REAR ENGINE UNDER COVER LH (for 5ZR-FXE)

    Click here

  38. INSTALL REAR ENGINE UNDER COVER RH (for 2ZR-FXE)

    Click here

  39. INSTALL REAR ENGINE UNDER COVER RH (for 5ZR-FXE)

    Click here

  40. INSPECT SPEED SENSOR SIGNAL

    Click here