LANE DEPARTURE ALERT SYSTEM(w/ Steering Control), Diagnostic DTC:C1A73

DTC Code DTC Name
C1A73 Driving Support ECU Receive Data Malfunction

DESCRIPTION

If a communication error between the driving support ECU assembly and another ECU is detected, DTC C1A73 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A73 Driving Support ECU Receive Data Malfunction 2 seconds after the power switch is turned on (IG), a communication error between the driving support ECU assembly and other ECUs is detected 5 seconds or more.

  • CAN communication system

  • Forward recognition camera

  • Driving support ECU assembly

CAUTION / NOTICE / HINT

Note


  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

  • If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

    Click here

  • When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

  • The lane departure alert system (w/ steering control) uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here

PROCEDURE


  1. CHECK FOR DTCs (PRE-COLLISION SYSTEM)

    Tech Tips

    The driving support ECU communicates with other ECUs via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.

    5. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC U0125, U0126, U0129, U0235, U023A, U0293, U1002 and U1104 are not output A
      DTC U0125, U0126, U0129, U0235, U023A, U0293, U1002 or U1104 are out put B

    B

    GO TO PRE-COLLISION SYSTEM Click here

    A

  2. CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Clear the DTCs.

      Click here

    6. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 7 seconds or more.

    7. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC C1A73 is not output A
      DTC C1A73 is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

  3. REPLACE FORWARD RECOGNITION CAMERA


    1. Replace the forward recognition camera.

      Click here

    2. Perform forward recognition camera adjustment.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Clear the DTCs.

      Click here

    6. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 7 seconds or more.

    7. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC C1A73 is not output A
      DTC C1A73 is output B

    A

    END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

    B

    REPLACE DRIVING SUPPORT ECU ASSEMBLY Click here