HYBRID CONTROL SYSTEM, Diagnostic DTC:P0E05-328, P0E09-336, P1C3E-333, P1C3F-341, P1C54-326, P1C59-334, P1C71-515, P1C72-516

DTC Code DTC Name
P0E05-328 Generator Phase V Current Sensor Circuit Range / Performance
P0E09-336 Generator Phase W Current Sensor Circuit Range / Performance
P1C3E-333 Generator Phase V Current Sensor Correlation
P1C3F-341 Generator Phase W Current Sensor Correlation
P1C54-326 Generator Phase V Current Sensor Sub Circuit Range / Performance
P1C59-334 Generator Phase W Current Sensor Sub Circuit Range / Performance
P1C71-515 Generator Phase V Current Sensor Offset Range / Performance
P1C72-516 Generator Phase W Current Sensor Offset Range / Performance

DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors the generator inverter current sensors. P0E05-328, P0E09-336, P1C3E-333, P1C3F-341, P1C54-326, P1C59-334, P1C71-515 and P1C72-516 indicate malfunctions in the current sensors, and they do not indicate malfunctions in the high-voltage system.

DTC No. INF Code DTC Detection Condition Trouble Area
P0E05 328 Malfunction in generator inverter current sensor (phase V main sensor) Inverter with converter assembly
P0E09 336 Malfunction in generator inverter current sensor (phase W main sensor)
P1C3E 333 Malfunction in generator inverter current sensor (performance problem or open phase V)
P1C3F 341 Malfunction in generator inverter current sensor (performance problem or open phase W)
P1C54 326 Malfunction in generator inverter current sensor (phase V sub sensor)
P1C59 334 Malfunction in generator inverter current sensor (phase W sub sensor)
P1C71 515 Malfunction in generator inverter current sensor (phase V main and sub sensors offset)
P1C72 516 Malfunction in generator inverter current sensor (phase W main and sub sensors offset)

PROCEDURE


  1. CHECK DTC OUTPUT (HV)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / DTC.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      P0E05-328, P0E09-336, P1C3E-333, P1C3F-341, P1C54-326, P1C59-334, P1C71-515 or P1C72-516 only is output. A
      P0A7A-203 is output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (P0A7A-203) Click here

    A

  2. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

    CAUTION:

    Be sure to wear insulated gloves.


    1. B001L9I

      Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

      Note

      Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

    2. Check the connection of the low voltage connector of the inverter with converter assembly.

      OK
      The connector is connected securely and there are no contact problems.

      Tech Tips

      When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.


    OK

    REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS Click here

    NG

    CONNECT SECURELY