HYBRID CONTROL SYSTEM, Diagnostic DTC:P06B0-163, P06D6-511, P06E6-164, P0A1A-151, P0A1A-166, P0A1A-658, P0A1A-791, P0A1B-198, P0A1B-786, P0A1B-794, P1C2A-155, P1C2B-192, P1C73-512, P1CA6-156, P1CA7-193, P3133-659, P3134-661

DTC Code DTC Name
P06B0-163 Sensor Power Supply "A" Circuit / Open
P06D6-511 Sensor Reference Voltage "F" Circuit / Open
P06E6-164 Sensor Power Supply "C" Circuit / Open
P0A1A-151 Generator Control Module
P0A1A-166 Generator Control Module
P0A1A-658 Generator Control Module
P0A1A-791 Generator Control Module
P0A1B-198 Drive Motor "A" Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1B-794 Drive Motor "A" Control Module
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator

DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P06B0 163 IPM positive power source error Inverter with converter assembly
P06D6 511 Standard voltage for analog signal offset
P06E6 164 IPM negative power source error
P0A1A 151 Run pulse signal cycle deviation or stop
P0A1A 166 R/D converter NM stop error
P0A1A 658 ALU error
P0A1A 791 R/D converter communication error
P0A1B 198 R/D converter NM stop error
P0A1B 786 ALU error
P0A1B 794 R/D converter communication error
P1C2A 155 A/D converter error
P1C2B 192 A/D converter error
P1C73 512 Standard voltage for analog signal error
P1CA6 156 CPU ROM-RAM error
P1CA7 193 CPU ROM-RAM error
P3133 659 Communication error (from MG1 to MG2)
P3134 661 Communication error (from MG2 to MG1)

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      None of the following DTCs are output. A
      Any of the following DTCs are output. B
      DTC No. Relevant Diagnosis
      P06B0-163 Sensor Power Supply "A" Circuit / Open
      P06D6-511 Sensor Reference Voltage "F" Circuit /Open
      P06E6-164 Sensor Power Supply "C" Circuit / Open
      P0A1A-166, 658, 791 Generator Control Module
      P0A1B-198, 786, 794 Drive Motor "A" Control Module
      P1C2A-155 Generator A/D Converter Circuit
      P1C2B-192 Drive Motor "A" A/D Converter Circuit
      P1C73-512 Sensor Standard Voltage "F" Circuit /Open
      P1CA6-156 Generator Control Module Malfunction
      P1CA7-193 Drive Motor Control Module Malfunction
      P3134-661 Communication Error from Drive Motor "A" to Generator

    5. Turn the power switch off.


    B

    REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS Click here

    A

  2. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Only DTC P0A1A-151, P3133-659 or P324E-788 is output. A
      Other than above. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  3. CLEAR DTC


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / DTC.

    4. Clear DTCs and freeze frame data.


    NEXT

  4. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch off and wait for 30 seconds or more.

    3. Turn the power switch on (IG) and wait for 5 seconds or more.

    4. Turn the power switch on (READY).

    5. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    6. Check if DTCs are output.

      Result
      Result Proceed to
      No DTCs are output (not including history DTCs). A
      Only DTC P0A1A-151, P3133-659 or P324E-788 is output. B
      Other than above. C

    7. Turn the power switch off.


    A

    REPLACE MG CONTROL COMPUTER Click here

    B

    REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER Click here

    C

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here