PARKING BRAKE PEDAL(for RHD) INSTALLATION

PROCEDURE


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. B001LWT

      Install the parking brake control pedal assembly with the 2 bolts and nut.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
    2. B001NEL

      Connect the parking brake switch connector.

    3. Engage the wire harness clamp.

    4. B001LOZE03
      Text in Illustration
      *a Fulcrum Length

      Using SST, install the bolt (A).

      SST
      09961-00950
      Torque:
      without SST
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
      with SST
      9.4 N*m  { 96 kgf*cm, 83 in.*lbf }

      Note


      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • This torque value is effective when SST is parallel to the torque wrench.

    5. Install the No. 1 parking brake cable assembly with the 4 bolts.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }

    6. Engage the cable with the clamp.

    7. B001L2SE02
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Temporarily install the lock nut.

      Tech Tips

      After adjusting parking brake pedal travel, tighten the lock nut.

  2. CONNECT NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    1. B001KTUE01
      Text in Illustration
      *a Turn
      *b Hold

      Connect the No. 1 parking brake pull rod sub-assembly to the parking brake control pedal assembly as shown in the illustration.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

    Click here

  4. INSTALL FRONT FLOOR CENTER REINFORCEMENT


    1. B001KGB

      Install the front floor center reinforcement with the 4 bolts.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

  5. INSTALL YAW RATE AND ACCELERATION SENSOR

    Click here

  6. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. Install the No. 2 console box mounting bracket with the 2 bolts.

    2. Engage the clamp.

  7. INSTALL NO. 1 ELECTRICAL KEY OSCILLATOR

    Tech Tips

    This is symmetrical to the LHD model Click here.

  8. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET

    Tech Tips

    This is symmetrical to the LHD model Click here.

  9. INSTALL NO. 3 CONSOLE BOX MOUNTING BRACKET

    Tech Tips

    This is symmetrical to the LHD model Click here.

  10. INSTALL CONSOLE BOX LH

    Tech Tips

    This is symmetrical to the LHD model Click here.

  11. INSTALL FRONT NO. 2 CONSOLE BOX INSERT

    Tech Tips

    This is symmetrical to the LHD model Click here.

  12. INSTALL CONSOLE BOX RH

    Tech Tips

    This is symmetrical to the LHD model Click here.

  13. INSTALL CONSOLE BOX INSERT

    Tech Tips

    This is symmetrical to the LHD model Click here.

  14. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY

    Tech Tips

    This is symmetrical to the LHD model Click here.

  15. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

    Tech Tips

    Perform the same procedure as for the LHD model Click here.

  16. INSTALL REAR CONSOLE BOX ASSEMBLY

    Tech Tips

    This is symmetrical to the LHD model Click here.

  17. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY

    Tech Tips

    This is symmetrical to the LHD model Click here.

  18. ADJUST PARKING BRAKE PEDAL TRAVEL

    Click here

  19. INSPECT BRAKE WARNING LIGHT

    Click here