POWER TRUNK LID SYSTEM Power Trunk Lid does not Operate

DESCRIPTION

The main body ECU (driver side junction block) continuously monitors the luggage door opening cancel switch. When the luggage door opening cancel switch is OFF, a luggage door opening switch signal is sent to the luggage closer motor assembly from the main body ECU (driver side junction block) via CAN communication. This actuates the power trunk opener operation, which opens the luggage door. When the luggage compartment door closer switch is ON, the luggage closer motor actuates the power trunk closer operation. When the key is held or all doors are unlocked and the electrical key transmitter sub-assembly is not held, and the luggage electrical key switch is ON or the key's luggage compartment door opener switch is pressed, the luggage closer motor assembly actuates the power trunk lid opener operation.

WIRING DIAGRAM

A001D4ZE05

CAUTION / NOTICE / HINT

Note

Before replacing the television camera (luggage electrical key switch), refer to the parking assist monitor system initialization Click here.

Tech Tips

Since the power trunk lid system has functions that use CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

PROCEDURE


  1. CHECK LUGGAGE CLOSER FUNCTION


    1. Set the luggage door so that it is ajar, and check that the closer motor operates normally.

      Result
      Result Proceed to
      Closer motor operates normally A
      Closer motor does not operate normally B

    B

    GO TO OTHER PROBLEM Click here

    A

  2. READ VALUE USING GTS


    1. Check the Data List for proper functioning of the switches Click here.

      Main Body (Main body ECU)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Trunk/BDoor Open SW Luggage door opening switch signal / ON or OFF

      ON: Luggage door opening switch is ON

      OFF: Luggage door opening switch is OFF

      		 -
      Trunk Main SW Luggage door opening cancel switch signal / ON or OFF

      ON: Luggage door opening cancel switch is ON

      OFF: Luggage door opening cancel switch is OFF

      		 -
      Result
      Result Proceed to
      Luggage door opening switch signal malfunction A
      Luggage door opening cancel switch signal malfunction B
      Data List normal C

    B

    INSPECT LUGGAGE DOOR OPENING CANCEL SWITCH Click here

    C

    READ VALUE USING GTS Click here

    A

  3. INSPECT LUGGAGE DOOR OPENING SWITCH SWITCH

    A001DSQE03
    *1 for LHD:
    *2 Component without harness connected: (Luggage Door Opening Switch)
    *3 for RHD:

    1. Remove the luggage door opening switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      3 (L) - 4 (B) Luggage door opening switch ON Below 1 Ω
      3 (L) - 4 (B) Luggage door opening switch OFF 10 kΩ or higher

    NG

    REPLACE LUGGAGE DOOR OPENER SWITCH Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR OPENING SWITCH - MAIN BODY ECU AND BODY GROUND)

    A0019LHE01
    *1 Front view of wire harness connected: (to Main Body ECU)
    *2 Front view of wire harness connected: (to Luggage Door Opening Switch)

    1. Disconnect the L3 switch connector.

    2. Disconnect the L13 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      L3-3 (L) - Body ground Always Below 1 Ω
      L3-4 (B) - L13-26 (TSW) Always Below 1 Ω
      L3-4 (B) - Body ground Always 10 kΩ or higher

    OK

    REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. INSPECT LUGGAGE DOOR OPENING CANCEL SWITCH

    A001AIAE11
    *1 Component without harness connected: (Luggage Door Opening Cancel Switch)

    1. Remove the luggage door opening cancel switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      1 - 2 Cancel switch ON Below 1 Ω
      1 - 2 Cancel switch OFF 10 kΩ or higher

    NG

    REPLACE LUGGAGE DOOR OPENER CANCEL SWITCH Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR OPENING CANCEL SWITCH - MAIN BODY ECU AND BODY GROUND)

    A001ECPE01
    *1 Front view of wire harness connector: (to Main Body ECU)
    *2 Front view of wire harness connector: (to Luggage Door Opening Cancel Switch)
    *3 TMSW

    1. Disconnect the L83 switch connector.

    2. Disconnect the L11 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      L83-1 - Body ground Always Below 1 Ω
      L83-2 - L11-3 (TMSW) Always Below 1 Ω
      L83-2 - Body ground Always 10 kΩ or higher

    OK

    REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. READ VALUE USING GTS


    1. Check the Data List for proper functioning of the switches Click here.

      Back Door (Luggage closer motor assembly)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      PBD Close SW Luggage compartment door closer switch signal / ON or OFF

      ON: Luggage compartment door closer switch is ON

      OFF: Luggage compartment door closer switch is OFF

      		 -
      Back Door Handle SW Luggage electrical key switch signal / ON or OFF

      ON: Luggage electrical key switch is ON

      OFF: Luggage electrical key switch is OFF

      		 -
      Result
      Result Proceed to
      Luggage compartment door closer switch signal malfunction A
      Luggage electrical key switch signal malfunction B
      Data List normal C

    B

    INSPECT LUGGAGE ELECTRICAL KEY SWITCH Click here

    C

    READ VALUE USING GTS Click here

    A

  8. INSPECT LUGGAGE COMPARTMENT DOOR CLOSER SWITCH

    A001FMEE02
    *1 Component without harness connected: (Luggage Compartment Door Closer Switch)

    1. Remove the luggage compartment door closer switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      3 - 4 Door closer switch ON Below 1 Ω
      3 - 4 Door closer switch OFF 10 kΩ or higher

    NG

    REPLACE LUGGAGE COMPARTMENT DOOR CLOSER SWITCH Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (DOOR CLOSER SWITCH - LUGGAGE CLOSER MOTOR AND BODY GROUND)

    A001EBZE01
    *1 Front view of wire harness connector: (to Luggage Closer Motor)
    *2 Front view of wire harness connector: (to Luggae Compartment Door Closer Switch)
    *3 LDDN

    1. Disconnect the S40 switch connector.

    2. Disconnect the S43 motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      S40-3 - Body ground Always Below 1 Ω
      S40-4 - S43-4 (LDDN) Always Below 1 Ω
      S40-4 - Body ground Always 10 kΩ or higher

    OK

    REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  10. INSPECT LUGGAGE ELECTRICAL KEY SWITCH

    A001DUFE06
    *1 Component without harness connected: (Luggage Electrical Key Switch)

    1. Remove the luggage electrical key switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      5 - 10 Luggage electrical key switch OFF 10 kΩ or higher
      5 - 10 Luggage electrical key switch ON Below 1 Ω

    NG

    REPLACE LUGGAGE ELECTRICAL KEY SWITCH Click here

    OK

  11. CHECK HARNESS AND CONNECTOR (LUGGAGE ELECTRICAL KEY SWITCH - LUGGAGE CLOSER MOTOR AND BODY GROUND)

    A001DROE02
    *1 Front view of wire harness connector: (to Luggage Closer Motor)
    *2 Front view of wire harness connector: (to Luggage Electrical Key Switch)

    1. Disconnect the S85 switch connector.

    2. Disconnect the S43 motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      S85-10 - Body ground Always Below 1 Ω
      S85-5 - S43-19 (LPSW) Always Below 1 Ω
      S85-5 - Body ground Always 10 kΩ or higher

    OK

    REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. READ VALUE USING GTS


    1. Using the GTS, read the Data List Click here.

      Main Body (Main body ECU)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Trunk Link with Door Lock Luggage compartment door lock function / ON or OFF Customized value displayed -
      Result
      Result Proceed to
      Luggage compartment door lock function is ON (There is a malfunction when only the luggage electrical key switch is operated [all doors are unlocked and the electrical key transmitter sub-assembly is not held]). A
      Luggage compartment door lock function is OFF (There is a malfunction when only the luggage electrical key switch is operated [electrical key transmitter sub-assembly is held]). B
      Luggage compartment door lock function is ON (There is a malfunction when only the luggage electrical key switch is operated [electrical key transmitter sub-assembly is held]). C
      Luggage compartment door lock function is OFF (There is a malfunction when only the luggage electrical key switch is operated [all doors are unlocked and the electrical key transmitter sub-assembly is not held]). D

    A

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    B

    GO TO ENTRY AND START SYSTEM Click here

    C

    PERFORM CUSTOMIZE SETTING (Proceed to Customize Parameters) Click here