CLIMATE CONTROL SEAT SYSTEM Climate Control System does not Operate on Rear Right Side

DESCRIPTION

When the seat heater switch is operated, the rear power seat switch receives the signal. The rear power seat switch then sends the signal to the seat climate control ECU through LIN communication. The seat climate control ECU receives the signal and operates the air seat.

WIRING DIAGRAM

A001F7EE09

CAUTION / NOTICE / HINT

Note

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no LIN communication malfunctions before troubleshooting this problem.

PROCEDURE


  1. CONFIRM PROBLEM SYMPTOMS

    Result
    Result Proceed to
    Air conditioner and heater do not operate A
    Heater is normal and air conditioner does not operate B
    Air conditioner is normal and heater does not operate C

    B

    CONFIRM TROUBLE AREAS Click here

    C

    READ VALUE USING INTELLIGENT TESTER (REAR POWER SEAT MODULE SWITCH) Click here

    A

  2. READ VALUE USING INTELLIGENT TESTER (REAR POWER SEAT MODULE SWITCH)


    1. Check the Data List for proper functioning of the rear power seat module switch Click here.

      Rear Console Switch
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Rear Right Seat A/C Level Adjust Switch (Up) Rear right seat heater switch up signal / ON or OFF

      ON: Rear seat heater switch up ON

      OFF: Rear seat heater switch up OFF

      		 -
      Rear Right Seat A/C Level Adjust Switch (Down) Rear right seat heater switch down signal / ON or OFF

      ON: Rear seat heater switch down ON

      OFF: Rear seat heater switch down OFF

      		 -
      Rear Right Seat A/C Auto Switch Rear right seat heater switch auto signal / ON or OFF

      ON: Rear seat heater switch auto ON

      OFF: Rear seat heater switch auto OFF

      		 -
      OK
      Tester display changes normally when Climate control switch (RH side) is operated
      Result
      Result Proceed to
      NG (except 4-Passenger with Ottoman) A
      NG (for 4-Passenger with Ottoman) B
      OK (w/o Ottoman) C
      OK (w/ Ottoman) D

    A

    REPLACE REAR POWER SEAT MODULE SWITCH Click here

    B

    REPLACE REAR POWER SEAT MODULE SWITCH Click here

    C

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    D

    REPLACE SEAT CLIMATE CONTROL ECU Click here

  3. CONFIRM TROUBLE AREAS

    Result
    Result Proceed to
    Cushion and seatback sides do not operate A
    Cushion side does not operate B
    Seatback side does not operate C

    B

    PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIRFLOW) Click here

    C

    PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIRFLOW) Click here

    A

  4. READ VALUE USING INTELLIGENT TESTER (REAR POWER SEAT MODULE SWITCH)


    1. Check the Data List for proper functioning of the rear power seat module switch Click here.

      Rear Console Switch
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Rear Right Seat A/C Level Adjust Switch (Up) Rear right seat heater switch up signal / ON or OFF

      ON: Rear seat heater switch up ON

      OFF: Rear seat heater switch up OFF

      		 -
      Rear Right Seat A/C Level Adjust Switch (Down) Rear right seat heater switch down signal / ON or OFF

      ON: Rear seat heater switch down ON

      OFF: Rear seat heater switch down OFF

      		 -
      Rear Right Seat A/C Auto Switch Rear right seat heater switch auto signal / ON or OFF

      ON: Rear seat heater switch auto ON

      OFF: Rear seat heater switch auto OFF

      		 -
      OK
      Tester display changes normally when climate control switch (RH side) is operated
      Result
      Result Proceed to
      OK A
      NG (for 4-Passenger with Ottoman) B
      NG (except 4-Passenger with Ottoman) C

    B

    REPLACE REAR POWER SEAT MODULE SWITCH Click here

    C

    REPLACE REAR POWER SEAT MODULE SWITCH Click here

    A

  5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COOL AIR)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check the climate control seat function Click here.

      Rear Right Seat A/C
      Tester Display Test Part Control Range
      Cool air Cool air operation OFF / ON
      OK
      Cool air operates normally
      Result
      Result Proceed to
      NG A
      OK (w/o Ottoman) B
      OK (w/ Ottoman) C

    B

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    C

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    A

  6. CHECK SEAT CLIMATE CONTROL CONTROLLER RH


    1. w/o Ottoman:

      Replace the seat climate control controller RH Click here.

    2. w/ Ottoman:

      Replace the seat climate control controller RH Click here.

    3. Check if the climate control seat function is normal.

      OK
      Climate control seat function is normal

    OK

    END (SEAT CLIMATE CONTROL CONTROLLER RH WAS DEFECTIVE)

    NG

  7. CHECK REAR SEATBACK CLIMATE CONTROL BLOWER RH


    1. w/o Ottoman:

      Replace the rear seatback climate control blower RH Click here.

    2. w/ Ottoman:

      Replace the rear seatback climate control blower RH Click here.

    3. Check if the climate control seat function is normal.

      OK
      Climate control seat function is normal

    OK

    END (REAR SEATBACK CLIMATE CONTROL BLOWER RH WAS DEFECTIVE)

    NG

  8. CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL ECU - SEAT CLIMATE CONTROL CONTROLLER RH AND REAR SEATBACK CLIMATE CONTROL BLOWER RH)


    1. Disconnect the f8 ECU connector.

      A001EOWE02

    2. Disconnect the p1 climate control controller connector.

    3. Disconnect the f12 climate control blower connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      f8-8 (TDC+) - p1-1 (TDC-) Always Below 1 Ω
      f8-7 (TDC-) - f12-2 (TDB-) Always Below 1 Ω
      p1-2 (TDC+) - f12-1 (TDB+) Always Below 1 Ω
      f8-8 (TDC+) - Body ground Always 10 kΩ or higher
      f8-7 (TDC-) - Body ground Always 10 kΩ or higher
      p1-2 (TDC+) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (w/o Ottoman) A
      OK (w/ Ottoman) B
      NG C

    A

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    B

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIRFLOW)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check the blower motor function Click here.

      Rear Right Seat A/C
      Tester Display Test Part Control Range
      Airflow Airflow operation OFF / Low / High
      OK
      Blower motor operates normally
      Result
      Result Proceed to
      OK (w/o Ottoman) A
      OK (w/ Ottoman) B
      NG C

    A

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    B

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    C

  10. CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL ECU - SEAT CLIMATE CONTROL BLOWER RH)


    1. A001F21E03

      Disconnect the f8 ECU connector.

    2. Disconnect the p2 climate control blower connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      f8-4 (BFC+) - p2-2 (BFC+) Always Below 1 Ω
      f8-6 (BFC-) - p2-4 (BFC-) Always Below 1 Ω
      f8-5 (BCS) - p2-3 (BCS) Always Below 1 Ω
      f8-4 (BFC+) - Body ground Always 10 kΩ or higher
      f8-6 (BFC-) - Body ground Always 10 kΩ or higher
      f8-5 (BCS) - Body ground Always 10 kΩ or higher
      f8-4 (BFC+) - f8-6 (BFC-) Always 10 kΩ or higher
      f8-5 (BCS) - f8-4 (BFC+) Always 10 kΩ or higher
      f8-5 (BCS) - f8-6 (BFC-) Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK SEAT CLIMATE CONTROL ECU


    1. A001BXVE01
      *1 Front view of wire harness connector: (to Seat Climate Control Blower RH)
      *2 BFC+
      *3 BFC-

      Disconnect the p2 blower connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      p2-2 (BFC+) - p2-4 (BFC-) Engine switch off → on (IG) Below 1 V → 11 to 14 V
      Result
      Result Proceed to
      OK (w/o Ottoman) A
      OK (w/ Ottoman) B
      NG (w/o Ottoman) C
      NG (w/ Ottoman) D

    A

    REPLACE SEAT CLIMATE CONTROL BLOWER RH Click here

    B

    REPLACE SEAT CLIMATE CONTROL BLOWER RH Click here

    C

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    D

    REPLACE SEAT CLIMATE CONTROL ECU Click here

  12. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIRFLOW)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check the blower motor function Click here.

      Rear Right Seat A/C
      Tester Display Test Part Control Range
      Airflow Airflow operation OFF / Low / High
      OK
      Blower motor operates normally
      Result
      Result Proceed to
      OK (w/o Ottoman) A
      OK (w/ Ottoman) B
      NG C

    A

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    B

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    C

  13. CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL ECU - REAR SEATBACK CLIMATE CONTROL BLOWER RH)


    1. A001CWLE02

      Disconnect the f8 ECU connector.

    2. Disconnect the f11 climate control blower connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      f8-24 (BFB+) - f11-2 (BFB+) Always Below 1 Ω
      f8-26 (BFB-) - f11-4 (BFB-) Always Below 1 Ω
      f8-25 (BBS) - f11-3 (BBS) Always Below 1 Ω
      f8-24 (BFB+) - Body ground Always 10 kΩ or higher
      f8-26 (BFB-) - Body ground Always 10 kΩ or higher
      f8-25 (BBS) - Body ground Always 10 kΩ or higher
      f8-24 (BFB+) - f8-26 (BFB-) Always 10 kΩ or higher
      f8-25 (BBS) - f8-24 (BFB+) Always 10 kΩ or higher
      f8-25 (BBS) - f8-26 (BFB-) Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. CHECK SEAT CLIMATE CONTROL ECU


    1. A001BCSE01
      *1 Front view of wire harness connector: (to Rear Seatback Climate Control Blower RH)
      *2 BFB+
      *3 BFB-

      Disconnect the f11 blower connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      f11-2 (BFB+) - f11-4 (BFB-) Engine switch off → on (IG) Below 1 V → 11 to 14 V
      Result
      Result Proceed to
      OK (w/o Ottoman) A
      OK (w/ Ottoman) B
      NG (w/o Ottoman) C
      NG (w/ Ottoman) D

    A

    REPLACE SEAT CLIMATE CONTROL BLOWER RH Click here

    B

    REPLACE SEAT CLIMATE CONTROL BLOWER RH Click here

    C

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    D

    REPLACE SEAT CLIMATE CONTROL ECU Click here

  15. READ VALUE USING INTELLIGENT TESTER (REAR POWER SEAT MODULE SWITCH)


    1. Check the Data List for proper functioning of the rear power seat module switch Click here.

      Rear Console Switch
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Rear Right Seat A/C Level Adjust Switch (Up) Rear right seat heater switch up signal / ON or OFF

      ON: Rear seat heater switch up ON

      OFF: Rear seat heater switch up OFF

      		 -
      Rear Right Seat A/C Level Adjust Switch (Down) Rear right seat heater switch down signal / ON or OFF

      ON: Rear seat heater switch down ON

      OFF: Rear seat heater switch down OFF

      		 -
      Rear Right Seat A/C Auto Switch Rear right seat heater switch auto signal / ON or OFF

      ON: Rear seat heater switch auto ON

      OFF: Rear seat heater switch auto OFF

      		 -
      OK
      Tester display changes normally when climate control switch (RH side) is operated

    NG

    REPLACE REAR POWER SEAT MODULE SWITCH Click here

    OK

  16. INSPECT REAR SEATBACK COVER RH


    1. Remove the rear seatback cover RH.


    2. Inspect the rear seatback cover RH.


      Result
      Result Proceed to
      OK A
      NG (w/o Ottoman) B
      NG (w/ Ottoman) C

    B

    REPLACE REAR SEATBACK COVER RH Click here

    C

    REPLACE REAR SEATBACK COVER RH Click here

    A

  17. INSPECT REAR SEAT CUSHION COVER RH


    1. Remove the rear seat cushion cover RH.


    2. Inspect the rear seat cushion heater RH.


      Result
      Result Proceed to
      OK A
      NG (w/o Ottoman) B
      NG (w/ Ottoman) C

    B

    REPLACE REAR SEAT CUSHION COVER RH Click here

    C

    REPLACE REAR SEAT CUSHION COVER RH Click here

    A

  18. CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL ECU - REAR SEATBACK COVER RH AND BODY GROUND)


    1. A001FMQE02
      *1 Front view of wire harness connector: (to Seat Climate Control ECU)
      *2 Front view of wire harness connector: (to Rear Seatback Cover RH)

      Disconnect the f45 ECU connector.

    2. Disconnect the f44 seatback cover connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      f45-1 (AMP) - f44-5 (SWR) Always Below 1 Ω
      f45-1 (AMP) - Body ground Always 10 kΩ or higher
      f44-6 (E) - Body ground Always Below 1 Ω
      Result
      Result Proceed to
      OK (w/o Ottoman) A
      OK (w/ Ottoman) B
      NG C

    A

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    B

    REPLACE SEAT CLIMATE CONTROL ECU Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR