INSTRUMENT PANEL SAFETY PAD INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL NO. 3 INSTRUMENT PANEL STAY


    1. Attach the 5 claws to install the 5 No. 3 instrument panel stays.

  2. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Attach the 5 clips to install the instrument panel safety pad sub-assembly.

    2. Install the 2 bolts <E>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Install the 8 bolts <A> and nut <F>.

      A001BS9E03
      Text in Illustration
      *1 Bolt <A> *2 Bolt <E>
      *3 Nut <F> - -

    4. Attach the 2 claws to connect the cooler thermistor.

    5. Connect each connector and each wire harness clamp.

  3. INSTALL TIRE PRESSURE MONITOR RECEIVER ASSEMBLY (w/ Tire Pressure Warning System)

    Click here

  4. INSTALL TELEMATICS TRANSCEIVER (w/ G-BOOK System)

    Click here

  5. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY

    Click here

  6. INSTALL NO. 1 SPEAKER HOLE COVER

    Click here

  7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

    Click here

  8. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Click here

  9. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  10. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  11. INSTALL FRONT PILLAR GARNISH LH

    Click here

  12. INSTALL FRONT PILLAR GARNISH RH

    Click here

  13. INSTALL ACCESSORY METER ASSEMBLY

    Click here

  14. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Attach the 10 clips to install the instrument panel finish panel sub-assembly.

  15. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Connect each connector and each wire harness clamp.

    2. Install the glove compartment door assembly with the 5 screws <C>.

  16. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY

    Click here

  17. INSTALL LOWER INSTRUMENT PANEL

    Click here

  18. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. A001CFK

      Insert the 2 guides.

    3. Attach the 4 claws to install the No. 2 instrument panel under cover sub-assembly.

  19. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY


    1. Connect each connector.

    2. Attach the 12 clips to install the instrument cluster finish panel garnish assembly.

      A001D68

  20. INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY

    Click here

  21. INSTALL INSTRUMENT SIDE PANEL RH

    A001B5X

    1. Attach the 6 clips to install the instrument side panel RH.

  22. INSTALL CONSOLE BOX ASSEMBLY


    1. w/o Rear Seat Entertainment System:

      Click here

    2. for 5-Passenger with Ottoman:

      Click here

    3. w/ Disc Player:

      Click here

  23. INSTALL COMBINATION METER ASSEMBLY

    A001AHP

    1. Connect the connector and attach the 2 claws to close the connector cover.

    2. Install the combination meter assembly with the 4 screws.

  24. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

    A0018Z8

    1. Connect the 2 connectors.

    2. Attach the 2 clips to install the No. 2 instrument cluster finish panel sub-assembly.

    3. Install the 2 clips.

  25. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY


    1. Click here.

  26. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY

    Click here

  27. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A001B4O

    1. Connect each connector and each wire harness clamp.

    2. Attach the 2 claws to connect the DLC3.

    3. Attach the 2 claws to install the No. 1 instrument panel under cover sub-assembly.

    4. Install the 2 screws.

  28. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Connect each connector.

    2. Attach the 5 clips and claw to install the No. 1 instrument panel safety pad sub-assembly.

    3. Install the screw <C> and bolt.

    4. A00194D

      Attach the claw to install the switch base hole cover to the No. 1 instrument panel safety pad sub-assembly.

  29. INSTALL INSTRUMENT PANEL ORNAMENT

    A0019SW

    1. Connect the connector.

    2. Attach the 4 clips to install the instrument panel ornament.

  30. INSTALL INSTRUMENT SIDE PANEL LH

    A001A61

    1. Attach the 6 clips to install the instrument side panel LH.

  31. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  32. ENABLE AUTOAWAY/RETURN FUNCTION


    1. Restore the autoaway/return function setting to the previous condition by changing the customize parameter Click here.

  33. INSTALL COWL TOP VENTILATOR LOUVER

    Click here

  34. CHECK SRS WARNING LIGHT

    Click here