POWER WINDOW CONTROL SYSTEM Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION


WIRING DIAGRAM

A001BGYE01

PROCEDURE


  1. CHECK LIN COMMUNICATION SYSTEM


    1. Check for LIN communication system DTCs related to the power window control system.

      Result:
      Result Proceed to
      DTC is output A
      DTC is not output B

    A

    GO TO LIN COMMUNICATION SYSTEM Click here

    B

  2. CHECK FOR DTC (B2312)


    1. Check if DTC B2312 is output.

      Result:
      Result Proceed to
      DTC is output A
      DTC is not output B

    A

    GO TO DTC B2312 Click here

    B

  3. READ VALUE USING INTELLIGENT TESTER (REAR MOTOR RH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn ON the intelligent tester.

    4. Enter the following menus.


      1. Select: Body / RR-Door Motor / Data List /

    5. According to the display on tester, read the "Data List".

      RR Door-Motor:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door P/W Up SW Rear power window RH remote manual UP switch signal / ON or OFF

      ON: Rear power window RH remote manual UP switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      RR Door P/W Down SW Rear power window RH remote manual DOWN switch signal / ON or OFF

      ON: Rear power window RH remote manual DOWN switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      OK
      Tester display changes normally when rear power window switch RH is operated.

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH) Click here

    NG

  4. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - REAR SWITCH RH)


    1. Disconnect the O2 ECU connector.

      A001B0AE06
      *1 Front view of wire harness connector: (to Rear Door ECU RH)
      *2 Front view of wire harness connector: (to Rear Switch RH)

    2. Disconnect the O7 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      O2-25 (SGND) - O7-5 (GND) Always Below 1 Ω
      O2-25 (SGND) or O7-5 (GND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR DOOR ECU RH - REAR MOTOR RH)


    1. Disconnect the O3 ECU connector.

      A001997E08
      *1 Front view of wire harness connector: (to Rear Door ECU RH)
      *2 Front view of wire harness connector: (to Rear Motor RH)
      *3 PWE
      *4 BDRJ

    2. Disconnect the O8 motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      O3-5 (BDRJ) - O8-2 (B) Always Below 1 Ω
      O3-2 (PWE) - O8-1 (E) Always Below 1 Ω
      O3-5 (BDRJ) or O8-2 (B) - Body ground Always 10 kΩ or higher
      O3-2 (PWE) or O8-1 (E) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - REAR MOTOR RH)


    1. Disconnect the O7 switch connector.

      A001BT2E06
      *1 Front view of wire harness connector: (to Rear Switch RH)
      *2 Front view of wire harness connector: (to Rear Motor RH)
      *3 UP
      *4 DOWN

    2. Disconnect the O8 motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      O7-2 (UP) - O8-10 (UP1) Always Below 1 Ω
      O7-10 (DOWN) - O8-7 (DWN1) Always Below 1 Ω
      O7-2 (UP) or O8-10 (UP1) - Body ground Always 10 kΩ or higher
      O7-10 (DOWN) or O8-7 (DWN1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)

    A0019I6E01
    *1 Component without harness connected: (Power Window Regulator Switch)
    *2 UP
    *3 DOWN

    1. Remove the switch.

    2. Measure the resistance of the switch when the switch is operated.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      O7-2 (UP) - O7-5 (GND) Manual UP operation Below 1 Ω
      O7-10 (DOWN) - O7-5 (GND) Manual DOWN operation Below 1 Ω

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH) Click here

    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH) Click here