LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the menus.

    6. Enter the following menus:


      1. Select: Body Electrical / (desired system) / Data List /

    7. According to the display on the GTS, read the "Data List".

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Engine switch on (ACC) signal / ON or OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 "ON" is also displayed for this item when the engine switch is on (IG).
      IG SW Engine switch on (IG) signal / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 "OFF" is also displayed for this item when the engine switch is on (ACC).
      Stop Light SW Stop light switch/ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      D Door Courtesy SW Driver side door courtesy switch signal/ON or OFF

      ON: Driver side door is open

      OFF: Driver side door is closed

      		 -
      P Door Courtesy SW Passenger side door courtesy switch signal/ON or OFF

      ON: Passenger side door is open

      OFF: Passenger side door is closed

      		 -
      RL Door Courtesy SW Rear door courtesy switch LH signal/ON or OFF

      ON: Rear door LH is open

      OFF: Rear door LH is closed

      		 -
      RR Door Courtesy SW Rear door courtesy switch RH signal/ON or OFF

      ON: Rear door RH is open

      OFF: Rear door RH is closed

      		 -
      Instrument Panel Illumination Instrument panel illumination condition/ON or OFF

      ON: Instrument panel illumination is flowing

      OFF: Instrument panel illumination is not flowing

      		 -
      Hazard Switch Hazard signal/ON or OFF

      ON: Hazard warning signal switch ON

      OFF: Hazard warning signal switch OFF

      		 -
      Illumination Rate Info Condition of automatic light control sensor/0 to 2162.65 ms Condition value will be displayed -
      Auto H Beam STS0* Automatic high beam sensor current state/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error
      Auto H Beam STS1* Automatic high beam sensor current state past 1/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error
      Auto H Beam STS2* Automatic high beam sensor current state past 2/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error
      Auto H Beam STS3* Automatic high beam sensor current state past 3/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error
      Auto H Beam STS4* Automatic high beam sensor current state past 4/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error
      Auto H Beam STS5* Automatic high beam sensor current state past 5/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error
      Auto H Beam STS6* Automatic high beam sensor current state past 6/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error
      Auto H Beam STS7* Automatic high beam sensor current state past 7/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Current condition displayed

      Undetec: undetected

      CAM NA: camera detection malfunction

      No sens: no detection

      Hlight: oncoming vehicles with headlights on

      Taillgt: preceding vehicles with taillights on

      Speed: vehicle speed

      Daytime: daytime state

      Village: urban area

      Malfunc: malfunction

      Delay: standby mode

      Aim Lmt: aiming misalignment

      SAE Mod: SAE mode

      Undefin: undefined state

      LIN Err: LIN communication error

      • *: w/ Automatic High Beam System

      Combination Switch
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Light Auto Switch Headlight dimmer switch signal (AUTO position)/ON or OFF

      ON: Headlight dimmer switch AUTO position

      OFF: Headlight dimmer switch OFF

      		 -
      Tail Light Switch Headlight dimmer switch signal (TAIL position)/ON or OFF

      ON: Headlight dimmer switch TAIL position

      OFF: Headlight dimmer switch OFF

      		 -
      Head Light Switch Headlight dimmer switch signal (HEAD position)/ON or OFF

      ON: Headlight dimmer switch HEAD position

      OFF: Headlight dimmer switch OFF

      		 -
      Dimmer Hi Switch Headlight dimmer switch signal (high position)/ON or OFF

      ON: Headlight dimmer switch high position

      OFF: Headlight dimmer switch OFF

      		 -
      Front Fog Light Switch Headlight dimmer switch signal (Fr fog position)/ON or OFF

      ON: Front fog light switch ON

      OFF: Front fog light switch OFF

      		 -
      Rear Fog Light Switch Headlight dimmer switch signal (Rr fog position)/ON or OFF

      ON: Rear fog light switch ON

      OFF: Rear fog light switch OFF

      		 -
      Passing Light Switch Headlight dimmer switch signal (Flash position)/ON or OFF

      ON: Flash switch ON

      OFF: Flash switch OFF

      		 -
      Turn Right Switch Headlight dimmer switch signal (Turn R position)/ON or OFF

      ON: Turn signal switch Turn R position

      OFF: Turn signal switch OFF

      		 -
      Turn Left Switch Headlight dimmer switch signal (Turn L position)/ON or OFF

      ON: Turn signal switch Turn L position

      OFF: Turn signal switch OFF

      		 -
      Ignition Switch CAN Comm Engine switch signal (CAN)/ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      Ignition Switch Engine switch signal/ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 "OFF" is also displayed for this item when the engine switch is on (ACC).
      Body No. 5
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Clearance Light Tr Clearance light illumination condition display/OK - Overheat - Overload

      OK: Normal

      Overheat: ECU overheats

      Overload: ECU overload

      		 -
      Head Light LH HI Tr Headlight LH HI illumination condition display/OK - Overheat - Overload

      OK: Normal

      Overheat: ECU overheats

      Overload: ECU overload

      		 -
      Head Light RH HI Tr Headlight RH HI illumination condition display/OK - Overheat - Overload

      OK: Normal

      Overheat: ECU overheats

      Overload: ECU overload

      		 -
      IG SW Engine switch signal / ON or OFF position

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 "OFF" is also displayed for this item when the engine switch is on (ACC).
      Body No. 4
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tail Light Tr States of taillight/OK or Break

      OK: Taillight circuit is normal

      Break: Taillight circuit is malfunctioning

      		 Confirm that headlight dimmer switch is ON (TAIL or HEAD position)
      Stop Light Tr States of stop light/OK or Break

      OK: Stop light circuit is normal

      Break: Stop light circuit is malfunctioning

      		 Confirm that brake pedal is pressed
      High Mount Stop Light Tr States of high mount stop light/OK or Break

      OK: High mount stop light circuit is normal

      Break: High mount stop light circuit is malfunctioning

      		 Confirm that brake pedal is pressed
      Rear Fog Light Tr Rear fog light illumination condition display/OK or Break

      OK: Rear fog light circuit is normal

      Break: Rear fog light circuit is malfunctioning

      		 -
      IG SW Engine switch signal/ON or OFF position

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 "OFF" is also displayed for this item when the engine switch is on (ACC).
      Stop Light Switch Stop light switch/ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Backup Light Tr States of back-up light/OK or Break

      OK: Back-up light circuit is normal

      Break: Back-up light circuit is malfunctioning

      		 Confirm that shift lever in R
      Luggage Courtesy Switch Luggage compartment door courtesy switch condition display/ON or OFF

      ON: Luggage room courtesy switch ON

      OFF: Luggage room courtesy switch OFF

      		 -
      Back Door
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Courtesy SW Luggage room courtesy switch signal/ON or OFF

      ON: Luggage room courtesy switch ON

      OFF: Luggage room courtesy switch OFF

      		 -
      AFS (w/o Adaptive High Beam System)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Traveling Direction Traveling direction/Fwd or Not Fwd

      Fwd: Forward

      Not Fwd: Except forward

      		 -
      Headlight Low Beam State Headlight (low) condition/ON or OFF

      ON: Low beam headlights ON

      OFF: Low beam headlights OFF

      		 -
      Headlight High Beam State Headlight (high) condition/ON or OFF

      ON: High beam headlights ON

      OFF: High beam headlights OFF

      		 -
      Engine Engine condition/Run or Stop

      Run: Engine running

      Stop: Engine stopped

      		 -
      +B AFS ECU power source voltage/Min.: 0 V, Max.: 19.75 V 11 to 14 V -
      Height Sens Pw Supply Val Height control sensor power supply value/Min.: 0 V, Max.: 6.25 V Power supply voltage to height control sensor -
      Fr Height Sens Signal Val Front height control sensor signal/Min.: 0 V, Max.: 5 V Height control sensor vehicle height value -
      Rr Height Sens Signal Val Rear height control sensor signal/Min.: 0 V, Max.: 5 V Height control sensor vehicle height value -
      Steering Sens Signal Steering angle/Min.: -384 deg., Max.: 382.5 deg. Current steering position -
      Steering Sens Center Pos Steering angle sensor memory/Min.: - 3072 deg., Max.: 3070.5 deg. Steering position stored in steering angle sensor -
      VGRS Relative Angle VGRS relative angle/Min.: -3072 deg., Max.: 3070.5 deg. Steering position stored in VGRS ECU -
      FR Wheel Speed Front wheel RH speed/Min.: 0 km/h (0 mph), Max.: 327.67 km/h (196.60 mph) Current front wheel RH speed -
      FL Wheel Speed Front wheel LH speed/Min.: 0 km/h (0 mph), Max.: 327.67 km/h (196.60 mph) Current front wheel LH speed -
      Vehicle Speed Vehicle speed/Min.: 0 km/h (0 mph), Max.: 327.67 km/h (196.60 mph) Almost same as actual vehicle speed (When driving) -
      L Swivel Target Step Headlight swivel motor LH target step value/0 to 400 step 24 to 200 step -
      L Swivel Current Step Headlight swivel motor LH current step value/0 to 400 step 24 to 200 step -
      R Swivel Target Step Headlight swivel motor RH target step value/0 to 400 step 49 to 301 step -
      R Swivel Current Step Headlight swivel motor RH current step value/0 to 400 step 49 to 301 step -
      LR Leveling Target Step Headlight swivel motor LH (leveling portion) and RH target step value/0 to 500 step 65 to 384 step -
      L Leveling Current Step Headlight swivel motor LH (leveling portion) current step value/0 to 500 step 65 to 384 step -
      R Leveling Current Step Headlight swivel motor RH (leveling portion) current step value/0 to 500 step 65 to 384 step -
      Number Of Trouble Codes Number of diagnosis codes/Min.: 0, Max.: 255 - -
      AHS (w/ Adaptive High Beam System)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      AHS Switch Adaptive high beam system main switch condition/ON or OFF

      ON: Adaptive high beam system main switch on

      OFF: Adaptive high beam system main switch off

      		 -
      Traveling Direction Traveling direction/Fwd or Not Fwd

      Fwd: Forward

      Not Fwd: Except forward

      		 -
      Headlight Low Beam State Headlight (low) condition/ON or OFF

      ON: Low beam headlights ON

      OFF: Low beam headlights OFF

      		 -
      Headlight High Beam State Headlight (high) condition/ON or OFF

      ON: High beam headlights ON

      OFF: High beam headlights OFF

      		 -
      Engine Engine condition/Run or Stop

      Run: Engine running

      Stop: Engine stopped

      		 -
      Passing Light Switch Headlight dimmer switch high flash position (pass) signal/ON or OFF

      ON: Headlight dimmer switch in high flash position

      OFF: Headlight dimmer switch not in high flash position

      		 -
      AHS Operation Condition Adaptive high beam system operation condition/Approval or Failure

      Approval: Adaptive high beam system operation conditions met

      Failure: Adaptive high beam system operation conditions not met

      		 -
      Optical Axis Control State Beam axis control condition/ON or OFF

      ON: Beam axis control operating

      OFF: Beam axis control stopped

      		 -
      Low Beam RH Operation Request Low beam RH operation request/ON or OFF

      ON: Low beam RH operation request present

      OFF: Low beam RH operation request not present

      		 -
      Variable Shade Beam RH Operation Request Variable shade beam RH operation request/ON or OFF

      ON: Variable shade beam RH operation request present

      OFF: Variable shade beam RH operation request not present

      		 -
      High Beam RH Operation Request High beam RH operation request/ON or OFF

      ON: High beam RH operation request present

      OFF: High beam RH operation request not present

      		 -
      Low Beam LH Operation Request Low beam LH operation request/ON or OFF

      ON: Low beam LH operation request present

      OFF: Low beam LH operation request not present

      		 -
      Variable Shade Beam LH Operation Request Variable shade beam LH operation request/ON or OFF

      ON: Variable shade beam LH operation request present

      OFF: Variable shade beam LH operation request not present

      		 -
      High Beam LH Operation Request High beam LH operation request/ON or OFF

      ON: High beam LH operation request present

      OFF: High beam LH operation request not present

      		 -
      Low Beam RH Operation Low Beam RH operation condition/Stop or Move

      Stop: Low Beam RH stopped

      Move: Low Beam RH operating

      		 -
      Variable Shade Beam RH Operation Variable shade beam RH operation condition/Stop or Move

      Stop: Variable shade beam RH stopped

      Move: Variable shade beam RH operating

      		 -
      High Beam RH Operation High beam RH operation condition/Stop or Move

      Stop: High beam RH stopped

      Move: High beam RH operating

      		 -
      Low Beam LH Operation Low beam LH operation condition/Stop or Move

      Stop: Low beam LH stopped

      Move: Low beam LH operating

      		 -
      Variable Shade Beam LH Operation Variable shade beam LH operation condition/Stop or Move

      Stop: Variable shade beam LH stopped

      Move: Variable shade beam LH operating

      		 -
      High Beam LH Operation High beam LH operation condition/Stop or Move

      Stop: High beam LH stopped

      Move: High beam LH operating

      		 -
      +B AFS ECU power source voltage/Min.: 0 V, Max.: 19.75 V 11 to 14 V -
      Height Sens Pw Supply Val Height control sensor power supply value/Min.: 0 V, Max.: 6.25 V Power supply voltage to height control sensor -
      Fr Height Sens Signal Val Front height control sensor signal/Min.: 0 V, Max.: 5 V Height control sensor vehicle height value -
      Rr Height Sens Signal Val Rear height control sensor signal/Min.: 0 V, Max.: 5 V Height control sensor vehicle height value -
      Steering Sens Signal Steering angle/Min.: -384 deg., Max.: 382.5 deg. Current steering position -
      Steering Sens Center Pos Steering angle sensor memory/Min.: - 3072 deg., Max.: 3070.5 deg. Steering position stored in steering angle sensor -
      VGRS Relative Angle VGRS relative angle/Min.: -3072 deg., Max.: 3070.5 deg. Steering position stored in VGRS ECU -
      FR Wheel Speed Front wheel RH speed/Min.: 0 km/h (0 mph), Max.: 327.67 km/h (196.60 mph) Current front wheel RH speed -
      FL Wheel Speed Front wheel LH speed/Min.: 0 km/h (0 mph), Max.: 327.67 km/h (196.60 mph) Current front wheel LH speed -
      Vehicle Speed Vehicle speed/Min.: 0 km/h (0 mph), Max.: 327.67 km/h (196.60 mph) Almost same as actual vehicle speed (When driving) -
      L Swivel Target Step Headlight swivel motor LH target step value/0 to 400 step 24 to 200 step -
      L Swivel Current Step Headlight swivel motor LH current step value/0 to 400 step 24 to 200 step -
      R Swivel Target Step Headlight swivel motor RH target step value/0 to 400 step 49 to 301 step -
      R Swivel Current Step Headlight swivel motor RH current step value/0 to 400 step 49 to 301 step -
      LR Leveling Target Step Headlight swivel motor LH (leveling portion) and RH target step value/0 to 500 step 65 to 384 step -
      L Leveling Current Step Headlight swivel motor LH (leveling portion) current step value/0 to 500 step 65 to 384 step -
      R Leveling Current Step Headlight swivel motor RH (leveling portion) current step value/0 to 500 step 65 to 384 step -
      Number Of Trouble Codes Number of diagnosis codes/Min.: 0, Max.: 255 - -

  2. ACTIVE TEST

    Note

    When a Rear Junction Block ECU and Multiplex Network Front Light ECU (Front Controller) related vehicle switch is ON, Active Test items related to the vehicle switch are prohibited (double operation prohibition). Check that the vehicle switches are OFF before performing Active Tests.

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus:


      1. Select: Body Electrical / (desired system) / Active Test /

    6. According to the display on the GTS, perform the "Active Test".

      Main Body
      Tester Display Test Part Control Range
      Hazard Hazard signal OFF - ON
      Turn Light RH Relay Operation Turn signal light operation OFF - ON
      Turn Light LH Relay Operation Turn signal light operation OFF - ON
      Dimmer Signal Illumination dimming operation OFF - ON
      Interior Panel Relay Interior panel relay operation OFF - ON
      Indicator for Lighting Illumination of switch indicator operation OFF - ON
      Fr Foot Light Front and rear interior foot light illumination operation OFF - ON
      Instrument Panel Illumination Instrument panel illumination operation OFF - ON
      Driver Door
      Tester Display Test Part Control Range
      Foot Light Door mirror foot light illumination operation OFF - ON
      Courtesy Light Courtesy light operation OFF - ON
      Inside Handle Illumination Inside handle illumination operation OFF - ON
      Seat Memory Light Seat memory switch illumination operation OFF - ON
      Passenger Door
      Tester Display Test Part Control Range
      Foot Light Door mirror foot light illumination operation OFF - ON
      Courtesy Light Courtesy light operation OFF - ON
      Inside Handle Illumination Inside handle illumination operation OFF - ON
      Seat Memory Light Seat memory switch illumination operation OFF - ON
      P Manual SW LED Manual door lock switch illumination operation OFF - ON
      Rear Left Door
      Tester Display Test Part Control Range
      Courtesy Light Courtesy light operation OFF - ON
      Inside Handle Illumination Inside handle illumination operation OFF - ON
      Ashtray Light Ashtray light operation OFF - ON
      Seat Memory Light Seat memory switch illumination operation OFF - ON
      Rear Right Door
      Tester Display Test Part Control Range
      Courtesy Light Courtesy light operation OFF - ON
      Inside Handle Illumination Inside handle illumination operation OFF - ON
      Ashtray Light Ashtray light operation OFF - ON
      Seat Memory Light Seat memory switch illumination operation OFF - ON
      Body No. 4
      Tester Display Test Part Control Range
      Tail Light Taillight operation OFF - ON
      Rear Fog Light Rear fog light operation OFF - ON
      Backup Light Back-up light operation OFF - ON
      Stop Light Stop light operation OFF - ON
      High Mount Stop Light High mount stop light operation OFF - ON
      Driver Side Buckle Light Driver side seat buckle illumination operation OFF - ON
      Front Passenger Side Buckle Light Front passenger side seat buckle illumination operation OFF - ON
      Luggage Light Control Luggage compartment room light operation OFF - ON
      Body No. 5
      Tester Display Test Part Control Range
      Head Light Low Low beam headlight illumination operation OFF - ON
      Head Light High High beam headlight illumination operation OFF - ON
      Head Light HI DRL Operation DRL light illumination operation OFF - ON
      Front Fog Light Relay Front fog light illumination operation OFF - ON
      Clearance Light Operation Front clearance light illumination operation OFF - ON
      Head Light Cleaner Headlight cleaner motor operation OFF - ON
      AFS (w/o Adaptive High Beam System)
      Tester Display Test Part Control Range
      Drive The Leveling Motor Leveling motor operation Up - Down - Stop
      Drive Swivel Motor LH Swivel motor LH direction rotation Left - Right - Stop
      Drive Swivel Motor RH Swivel motor RH direction rotation Left - Right - Stop
      AFS Alarm Display System check screen on the multi-information display in the combination meter operation OFF - ON
      Automatic High Beam Operation* Automatic high beam system operation OFF - ON

      • *: w/ Automatic High Beam System

      AHS (w/ Adaptive High Beam System)
      Tester Display Test Part Control Range
      Drive The Leveling Motor Leveling motor operation Up - Down - Stop
      Drive Swivel Motor LH Swivel motor LH direction rotation Left - Right - Stop
      Drive Swivel Motor RH Swivel motor RH direction rotation Left - Right - Stop
      High Beam Indicator High beam indicator operation OFF - ON
      Advice Display Advice display operation OFF - ON
      Auto High Beam Control Indicator Adaptive high beam system indicator operation OFF - ON
      Auto High Beam Warning Indicator Adaptive high beam system warning indicator operation OFF - ON
      High Beam LH Switching LH LO/HI beam to high OFF - ON
      Variable Shade Beam LH Variable shade beam LH operation OFF - ON
      High Beam RH Switching RH LO/HI beam to high OFF - ON
      Variable Shade Beam RH Variable shade beam RH operation OFF - ON
      Variable Shade Beam LH/RH LH/RH variable shade beam operation OFF - ON
      Extra High Beam High beam headlight operation OFF - ON