REAR STABILIZER BAR REMOVAL

PROCEDURE


  1. DISCONNECT NO. 1 ACTUATOR HARNESS CLAMP

    Click here

  2. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

    Click here

  3. REMOVE REAR WHEEL

  4. REMOVE NO. 6 ROCKER PANEL MOULDING PROTECTOR


    1. Remove the protector for 1UR-FSE Click here.

    2. Remove the protector for 1UR-FE Click here.

  5. REMOVE NO. 5 ROCKER PANEL MOULDING PROTECTOR


    1. Remove the protector for 1UR-FSE Click here.

    2. Remove the protector for 1UR-FE Click here.

  6. REMOVE REAR WHEEL HOUSE LINER LH

    Click here

  7. REMOVE REAR WHEEL HOUSE LINER RH

    Tech Tips

    Use the same procedures described for the LH side.

  8. REMOVE REAR SPEED SENSOR LH

    Click here

  9. REMOVE REAR SPEED SENSOR RH

    Tech Tips

    Use the same procedures described for the LH side.

  10. REMOVE PARKING BRAKE CABLE

    A0019PLE02
    *1 Parking Brake Cable

    1. Remove the 2 nuts and disconnect the cable from the vehicle side.

  11. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH

    Click here

  12. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. REMOVE REAR STABILIZER LINK ASSEMBLY LH

    A0019GT

    1. Remove the nut and disconnect the stabilizer link from stabilizer bar.

    2. A001DVW

      Remove the bolt, nut and stabilizer link from the rear No. 2 suspension arm.

  14. REMOVE REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  15. DISCONNECT REAR SHOCK ABSORBER ASSEMBLY LH (w/o Air Suspension)

    Click here

  16. DISCONNECT REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  17. DISCONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH (w/ Air Suspension)

    Click here

  18. DISCONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  19. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. A00196AE02
      Text in Illustration
      *1 Attachment
      *2 Engine Lifter
      *a Attachment placement location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

      Note


      • Use the attachments to keep the rear suspension member sub-assembly level.

      • The rear suspension member sub-assembly is a heavy component. Make sure that it is supported securely.

    2. for Sports Package:

      A001C6YE04
      Text in Illustration
      *A for Sports Package *B for Standard
      *1 Suspension Member Stopper Lower RH *2 Suspension Member Stopper Lower LH

      1. Remove the 4 bolts labeled A.

      2. Remove the 4 bolts labeled B and 2 suspension member stoppers.

      3. Slowly lower the rear suspension member subassembly.

        Note

        When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

    3. for Standard:


      1. Remove the 4 bolts.

      2. Slowly lower the rear suspension member subassembly.

        Note

        When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

  20. REMOVE REAR STABILIZER BAR

    A001CWKE11
    *1 Suspension Member

    1. Remove the 4 bolts and stabilizer bar from the suspension member.

      Tech Tips

      The stabilizer bracket and bush are built onto the stabilizer bar. If the bracket and/or bush detach from the bar, replace the bar.