REAR AXLE HUB INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart ( Click here).

PROCEDURE


  1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH


    1. A001BLZ

      Install the parking brake plate, cable support bracket and parking brake anchor block to the rear axle carrier with the 2 nuts.

      Torque:
      76 N*m  { 775 kgf*cm, 56 ft.*lbf }

    2. Hold the axle hub and bearing in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    3. A001C1N

      Install the axle hub and bearing to the rear axle carrier with the 4 bolts.

      Torque:
      97 N*m  { 989 kgf*cm, 72 ft.*lbf }

  2. INSTALL REAR NO. 1 WHEEL BEARING DUST DEFLECTOR LH


    1. A001CE6E03
      *1 Matchmark
      *2 Dust Deflector

      Using SST and a hammer, install the No. 1 bearing dust deflector to the rear axle carrier.

      SST
      09950-70010   ( 09951-07150 )
      09951-01000

      Tech Tips

      Align the hole for the speed sensor in the No. 1 bearing dust deflector with the rear axle carrier.

  3. INSTALL REAR AXLE ASSEMBLY LH


    1. Engage the spline part of the rear axle carrier to the spline part of the driver shaft assembly.

    2. Using a jack, lift up the rear axle carrier, and align the installation positions of each arm.

      Note

      Place a wooden block between the jack and rear axle carrier to prevent damage.

  4. TEMPORARILY CONNECT REAR SHOCK ABSORBER ASSEMBLY LH (for Coil suspension)

    Click here

  5. TEMPORARILY CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH (for Air suspension)

    Click here

  6. CONNECT REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH


    1. A001BLH

      Connect the control arm with a new nut to the axle carrier.

      Torque:
      160 N*m  { 1632 kgf*cm, 118 ft.*lbf }

  7. CONNECT REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH


    1. A0019H0

      Connect the control arm with a new nut to the axle carrier.

      Torque:
      160 N*m  { 1632 kgf*cm, 118 ft.*lbf }

  8. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. A001C0G

      Install the stud of the suspension arm, and temporarily install a washer, nut and the bolt to the axle carrier.

    2. A001BJUE06
      *1 No. 2 Suspension Toe Adjust Plate

      Temporarily install the No. 2 suspension arm with the No. 2 suspension toe adjust plate, rear suspension toe adjust cam and nut to the suspension member.

  9. CONNECT TOE CONTROL LINK SUB-ASSEMBLY LH


    1. A001923

      Connect the control link with a new nut to the axle carrier.

      Torque:
      118 N*m  { 1203 kgf*cm, 87 ft.*lbf }

  10. CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. A001CJK

      Connect the suspension arm with a new nut to the axle carrier.

      Torque:
      118 N*m  { 1203 kgf*cm, 87 ft.*lbf }

  11. INSTALL PARKING BRAKE ASSEMBLY

    Click here

  12. INSTALL REAR AXLE SHAFT LH NUT


    1. Install a new rear axle shaft nut.

      Torque:
      290 N*m  { 2957 kgf*cm, 214 ft.*lbf }

  13. INSPECT REAR AXLE HUB BEARING LOOSENESS

    Click here

  14. INSPECT REAR AXLE HUB RUNOUT

    Click here

  15. INSTALL REAR DISC

    Click here

  16. ADJUST PARKING BRAKE SHOE CLEARANCE

    Click here

  17. CONNECT SPEED SENSOR REAR LH

    Click here

  18. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH


    1. A001E6L

      Connect the rear disc brake caliper assembly LH with new 2 bolts.

      Torque:
      86 N*m  { 877 kgf*cm, 63 ft.*lbf }

      Note


      • Do not twist the flexible hose.

      • Make sure the screw parts are free from foreign matter and are not damaged.

      • Be careful not to overtighten the bolts, as the rear axle carrier is made of aluminum.

  19. STAKE REAR AXLE SHAFT LH NUT


    1. A001FDP

      Using a chisel and a hammer, stake the axle shaft nut.

  20. INSTALL LOAD SENSING VALVE SENSOR BRACKET


    1. A001C12

      Install the load sensing valve sensor bracket to the toe control link sub-assembly with the bolt.

      Torque:
      3.6 N*m  { 37 kgf*cm, 70 kgf*cm, 32 in.*lbf, 61 in.*lbf }

  21. STABILIZE SUSPENSION (for Coil Suspension)

    Click here

  22. STABILIZE SUSPENSION (for Air Suspension)

    Click here

  23. CONNECT REAR SHOCK ABSORBER ASSEMBLY LH (for Coil suspension)

    Click here

  24. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH (for Air suspension)

    Click here

  25. CONNECT REAR STABILIZER LINK ASSEMBLY LH


    1. A001DVW

      Insert the bolt from the front of the vehicle. Then install the rear stabilizer link assembly LH with the nut.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

  26. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. A001BJU

      Tighten the nut on the rear suspension member side.

      Torque:
      150 N*m  { 1530 kgf*cm, 111 ft.*lbf }
    2. A001C0G

      Tighten the nut on the rear axle carrier side.

      Torque:
      225 N*m  { 2294 kgf*cm, 166 ft.*lbf }

  27. INSTALL REAR WHEEL

    Torque:
    140 N*m  { 1428 kgf*cm, 103 ft.*lbf }

  28. PERFORM PARKING BRAKE SHOE BEDDING


    1. Perform parking brake shoe bedding ( Click here).

  29. INSPECT AND ADJUST REAR WHEEL ALIGNMENT


    1. Inspect and adjust rear wheel alignment ( Click here).

  30. CHECK ABS SPEED SENSOR SIGNAL


    1. Check the speed sensor signal ( Click here).

  31. ADJUST HEADLIGHT ASSEMBLY

    Click here

  32. ADJUST OBJECT RECOGNITION CAMERA

    Click here