DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn on the intelligent tester.
Enter the following menus:
Powertrain / Cruise Control / Data List.
Body / Combination Meter / Data List.
According to the display on tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) | Actual vehicle speed is display | - |
| CCS Mem Vehicle Spd | Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) | Actual vehicle speed stored in memory | - |
| Throttle | Required throttle opening angle / min.: 0 deg, max.: 125 deg | Actual required throttle opening | - |
| Cruise Control | Cruise control / ON or OFF | ON: Cruise control is SET OFF: Cruise control is UNSET |
- |
| CCS Main SW M-CPU | Cruise control switch signal (Main CPU) / ON or OFF | ON: Cruise control switch is ON OFF: Cruise control switch is OFF |
- |
| CCS Relay M-CPU | Switch ready (Main CPU) / ON or OFF | ON: Switch ready (Main CPU) is SET OFF: Switch ready (Main CPU) is UNSET |
- |
| CCS Indicator M-CPU | Cruise control indicator signal (Main CPU) / ON or OFF | ON: "CCS READY" ON OFF: "CCS READY" OFF |
- |
| Cancel Switch | CANCEL switch signal / ON or OFF | ON: CANCEL switch ON OFF: CANCEL switch OFF |
- |
| SET/COAST Switch | -/SET switch signal / ON or OFF | ON: -/SET switch ON OFF: -/SET switch OFF |
- |
| RES/ACC Switch | +/RES switch signal / ON or OFF | ON: +/RES switch ON OFF: +/RES switch OFF |
- |
| Stop Light SW M-CPU | Stop light SW signal (Main CPU) / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| CCS Operation Status | Shift lever position signal / ON or OFF | ON: Shift lever position D (8th, 7th, 6th, 5th or 4th) OFF: Shift lever except position D (8th, 7th, 6th, 5th or 4th) |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Speed Meter | Vehicle speed / min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) | Actual vehicle speed is display | - |
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn on the intelligent tester.
Enter the following menus:
Body / Combination Meter / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indic. Lamp Cruise | Cruise control indicator light | ON / OFF | - |
| Indicat. SET | SET indicator light | ON / OFF | - |