OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. A001CRB

      Open the oil filler cap service hole cover.

    2. Remove the oil filler cap.

    3. Remove the oil pan drain plug and drain the engine oil into a container.

    4. Install a new gasket and the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  2. REMOVE OIL FILTER ELEMENT SERVICE HOLE COVER


    1. A001CY8

      Remove the screw.

    2. Open the service hole cover.

  3. REMOVE OIL FILTER ELEMENT


    1. A001DM3E01
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A001FPH

      Remove the oil filter drain plug.

    3. A001AJQE03
      Text in Illustration
      *1 Oil Filter Cap
      *2 Valve
      *3 Pipe
      *4 O-Ring
      *5 Hose

      Install the pipe to the oil filter cap.

      Note

      If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

      Tech Tips

      Use a container to catch the draining oil.

    4. A001B75

      Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

    5. A001FOLE02
      Text in Illustration
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. A001F1EE03
      Text in Illustration
      *1 O-Ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.

  4. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, the threads and O-ring groove.

    2. A001B7GE01
      Text in Illustration
      *1 O-Ring
      *a CORRECT
      *b INCORRECT

      Apply a small amount of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element to the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

      Note

      Do not pinch the O-ring for the cap.

    6. A001BWJE01
      Text in Illustration
      *1 Oil Filter Bracket
      *2 Oil Filter Cap
      *3 O-Ring
      *4 Oil Filter Bracket
      *a No Clearance

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • When tightening the oil filter cap, do not remove the oil filter bracket clip.

      • Make sure that the oil filter is installed securely as shown in the illustration.

      • Be careful that the O-ring does not get caught between the parts.

    7. A001EWOE02
      Text in Illustration
      *1 O-Ring

      Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

      Note

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. Install the oil filter drain plug.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

      Note

      Be careful that the O-ring does not get caught between the parts.

  5. ADD ENGINE OIL


    1. Add fresh oil.

      Standard engine oil
      Oil grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50
      Standard capacity
      Item Specified Condition
      Drain and refill without oil filter change 8.4 liters (8.9 US qts, 7.4 Imp. qts)
      Drain and refill with oil filter change 8.6 liters (9.1 US qts, 7.6 Imp. qts)
      Dry fill 10.2 liters (10.8 US qts, 9.0 Imp. qts)

    2. Install the oil filler cap.

    3. Close the oil filler cap service hole cover.

  6. INSPECT FOR ENGINE OIL LEAK

    Click here

  7. CHECK ENGINE OIL LEVEL

    Click here

  8. INSTALL OIL FILTER ELEMENT SERVICE HOLE COVER


    1. Install the service hole cover with the screw.