СТАРТЕР (для моделей мощностью 2,7 кВт) ПРОВЕРКА


  1. INSPECT STARTER ARMATURE ASSEMBLY


    1. A003FB5E01

      Using an ohmmeter, check that there is continuity between the segments of the commutator.

      If there is no continuity between any segment, replace the starter armature.

    2. A003DOAE01

      Using an ohmmeter, check the resistance between the commutator and armature coil core.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, replace the starter armature.

    3. A003CZX

      Check for the commutator circuit runout.


      1. Place the commutator on V-blocks.

      2. Using a dial indicator, measure the circle runout.

        Maximum runout
        0.05 mm (0.002 in.)

        If the runout is greater than the maximum, replace the starter armature.

    4. A003HDE

      Using vernier calipers, measure the commutator diameter.

      Standard diameter
      36.0 mm (1.417 in.)
      Minimum diameter
      35.0 mm (1.378 in.)

      If the diameter is less than the minimum, replace the starter armature.

    5. A003BO0

      Check that the undercut portion between the segments is free of foreign objects and measure its depth.

      Standard undercut depth
      0.7 mm (0.028 in.)
      Minimum undercut depth
      0.2 mm (0.008 in.)

      If the undercut depth is less than the minimum, correct it with a hacksaw blade.

  2. INSPECT STARTER YOKE ASSEMBLY


    1. A003E7OE01

      Using an ohmmeter, check that there is continuity between the terminal C wire and brushes.

      If there is no continuity, replace the starter yoke assembly.

    2. A003H78E01

      Using an ohmmeter, check the resistance between the starter yoke body and brushes.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke.

  3. INSPECT STARTER BRUSH HOLDER ASSEMBLY


    1. A003HXFE01

      Using vernier calipers, measure the brush length.

      Standard length
      20.5 mm (0.807 in.)
      Minimum length
      11.0 mm (0.433 in.)

      If the length is less than the minimum, replace the brush holder and starter yoke.

    2. A003HYSE01

      Check the pull scale reading as soon as the brush spring is separated from the brush.

      Standard spring load
      26 to 45 N (2.7 to 4.6 kgf, 5.8 to 10.1 lbf)
      Minimum spring load
      12.4 N (1.3 kgf, 2.8 lbf)

      If the spring load is less than the minimum, replace the brush holder assembly.

    3. A003GIOE01

      Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

      Standard resistance
      10 kΩ or higher

      If the result is not as specified, repair or replace the brush holder assembly.

  4. INSPECT STARTER CLUTCH SUB-ASSEMBLY


    1. A003CF2E01

      Turn the clutch pinion gear clockwise and check that it turns freely. Try to turn the clutch pinion gear counterclockwise and check that it locks.

      If necessary, replace the starter clutch.

  5. INSPECT MAGNET STARTER SWITCH ASSEMBLY


    1. A003BFFE01

      Using an ohmmeter, check that there is continuity between terminals 50 and C.

      If there is no continuity, replace the magnet starter switch assembly.

    2. A003B58E01

      Using an ohmmeter, check that there is continuity between terminal 50 and the magnet switch body.

      If there is no continuity, replace the magnet starter switch assembly.