РАДИАТОР СНЯТИЕ


  1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)


    1. Запустите двигатель.

    2. Установите выключатель системы кондиционирования в положение ON (ВКЛ).

    3. С помощью компрессора прокачайте хладагент по системе кондиционирования при частоте вращения коленчатого вала двигателя приблизительно 1000 об/мин в течение 5-6 минут и соберите в компрессор системы кондиционирования, по возможности, все компрессорное масло, оставшееся в компонентах.

    4. Выключите двигатель.

    5. С помощью SST выпустите газообразный хладагент.

      SST
      07110-58060   ( 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080 )

  2. DRAIN ENGINE COOLANT

    A003F1ME01

    CAUTION:

    Для предотвращения ожогов не снимайте пробку расширительного бачка, пока двигатель и радиатор не охладятся. Тепловое расширение вызывает выброс из радиатора горячей охлаждающей жидкости и пара.


    1. Ослабьте пробку сливного отверстия радиатора.

    2. Снимите пробку расширительного бачка.

    3. Ослабьте пробку сливного отверстия блока цилиндров и слейте охлаждающую жидкость.

    4. Затяните пробку сливного отверстия радиатора.

    5. Затяните пробку сливного отверстия блока цилиндров.

      Torque:
      13 Н*м  { 130 кгс*см, 9 фунт-сила-футов }

  3. REMOVE FRONT BUMPER REINFORCEMENT


  4. REMOVE W/ RECEIVER CONDENSER ASSEMBLY (w/ Air Conditioning System)

    Click here

  5. REMOVE RADIATOR PROTECTOR (w/o Air Conditioning System)

    A003FZR

    1. Remove the 4 bolts and radiator protector.

  6. REMOVE UPPER RADIATOR SUPPORT SEAL

    A003CEW

    1. Remove the 4 clips, 4 bolts and upper radiator support seal.

  7. REMOVE RADIATOR RESERVOIR ASSEMBLY

    A003E3S

    1. Slide the hose clamp and disconnect the water by-pass hose from the radiator reservoir assembly.

    2. Slide the hose clamp and disconnect the No. 2 water by-pass hose from the radiator reservoir assembly.

    3. Remove the bolt and radiator reservoir assembly.

  8. REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

    A003HAF

    1. Disconnect the connector from the windshield washer motor and pump assembly.

    2. Remove the 2 bolts and windshield washer motor and pump assembly.

    3. Detach the hose clamp.

      A003C6KE01
      Text in Illustration
      *A w/ Rear Wiper *B w/o Rear Wiper

    4. w/ Rear Wiper:

      Disconnect the 2 connectors and 2 washer hoses.

    5. w/o Rear Wiper:

      Disconnect the connector and washer hose.

  9. REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY


    1. A003DDAE01
      Обозначения на рисунке
      *A Для моделей со стандартным кузовом
      *B Для моделей с широким кузовом

      Выверните 3 болта и снимите кронштейн замка капота в сборе.

  10. REMOVE HOOD LOCK ASSEMBLY

    A003E6M

    1. Remove the 3 bolts and disconnect the hood lock assembly.

    2. Disconnect the hood lock assembly from the hood lock control cable assembly.

  11. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    1. Slide the hose clamp and disconnect the water by-pass hose from the radiator assembly.

    2. Detach the 2 clamps to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.

      A003E0VE01
      Text in Illustration
      *A for LHD *B for RHD

    3. Remove the 6 bolts and upper radiator support sub-assembly.

  12. REMOVE NO. 1 RADIATOR AIR GUIDE (for Wide Body)


    1. Remove the 2 bolts and No. 1 radiator air guide.

  13. REMOVE NO. 2 RADIATOR AIR GUIDE (for Wide Body)


    1. Remove the 2 bolts and No. 2 radiator air guide.

  14. REMOVE FAN BRACKET SUB-ASSEMBLY

    A003H93

    1. Detach the clamp.

    2. Remove the 2 bolts, 2 nuts and fan bracket sub-assembly.

  15. REMOVE FAN SHROUD


    1. A003HS3E02
      Text in Illustration
      *A w/ Air Conditioning System
      *B w/o Air Conditioning System

      w/ Air Conditioning System:

      Detach the 2 clamps and disconnect the 2 connectors.

    2. w/o Air Conditioning System:

      Detach the 3 clamps and disconnect the connector.

    3. A003GKD

      Remove the 6 bolts and fan shroud from the underside of the vehicle.

  16. REMOVE NO. 2 FAN SHROUD


    1. Slide the hose clamp and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.

    2. A003I8PE01
      Text in Illustration
      *A for LHD
      *B for RHD

      Remove the bolt to disconnect the water by-pass pipe sub-assembly from the radiator assembly.

      Tech Tips

      This procedure is performed because the bolt of the water by-pass pipe sub-assembly interferes with the removal of the No. 2 fan shroud.

    3. A003HD7E02

      Remove the 2 bolts from the upper side of the vehicle, and then remove the No. 2 fan shroud from the underside of the vehicle.

      Tech Tips

      Do not damage the radiator assembly when removing the No. 2 fan shroud.

  17. REMOVE RADIATOR ASSEMBLY

    A003BA4

    1. Slide the 2 hose clamps and disconnect the No. 2 radiator hose and No. 3 radiator hose from the radiator assembly.

    2. Remove the radiator assembly from the vehicle.

      Note

      Do not drop the radiator assembly.

    3. Remove the 4 grommets from the radiator assembly.

  18. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

    A003CY2

    1. Slide the hose clamp and remove the water by-pass pipe sub-assembly from the radiator assembly.