КЛАПАН РОГ УСТАНОВКА


  1. TEMPORARILY TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY


    1. Temporarily tighten the EGR valve assembly with the sensor.


      1. A003DG5E01

        Install 2 new gaskets and the EGR valve to the intake air connector as shown in the illustration.

      2. A003HC0

        Temporarily tighten the intake air connector with EGR valve assembly to the intake manifold with the bolt and the 2 nuts.

      3. Install the vacuum hose to the intake air connector.

      4. Temporarily tighten the manifold stay with the bolt.

      5. A003H5T

        Connect the EGR valve position sensor connector.

      6. Connect the intake air temperature sensor connector.

    2. Install the vacuum regulating valve.


      1. A003BEQ

        Install the vacuum regulating valve with the 2 bolts.

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      2. Connect the 2 vacuum hoses and the regulating valve connector.

  2. INSTALL EGR PIPE SUB-ASSEMBLY NO.1


    1. A003BF9

      Install the 2 gaskets to the cylinder head and EGR pipe sub-assembly as shown in the illustration.

    2. A003CG8

      Install the EGR pipe sub-assembly with the 2 bolts and 2 nuts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

    3. Tighten the intake air connector with the bolt and the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    4. Tighten the manifold stay.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  3. REMOVE EGR PIPE SUB-ASSEMBLY NO.1


    1. Remove the 3 bolts, the 2 nuts, and the EGR pipe sub-assembly.

    2. Remove the 2 gaskets.

  4. INSTALL DIESEL THROTTLE BODY ASSEMBLY

    Note

    After removing and installing, or replacing the throttle body, be sure to perform the operation check.


    1. Install a new gasket to intake air connector.

    2. A003F09

      Install the throttle body with the 2 bolts and the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
    3. A003BFR

      Connect the 2 throttle body connectors.

  5. INSTALL AIR HOSE NO.4


    1. A003DQ1

      Install the air hose No.4 with the 2 clamps.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  6. INSTALL EGR PIPE SUB-ASSEMBLY NO.1


    1. A003BF9

      Install 2 new gaskets to the cylinder head and the EGR pipe sub-assembly No.1 as shown in the illustration.

    2. A003CG8

      Install the EGR pipe with the 2 bolts and the 2 nuts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }
    3. A003BPA

      Connect the fuel pressure sensor connector.

  7. CONNECT OIL RETURN HOSE (w/ Intercooler)


    1. A003ICN

      Connect the oil return hose with the clip.

  8. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY


    1. A003E43E01

      Установите масляный бачок лопастного насоса в сборе и закрепите 2 болтами.

      Torque:
      8,0 Н*м  { 82 кгс*см, 71 фунт-сила-дюйм }

  9. INSTALL ENGINE SERVICE HOLE COVER NO.2


    1. Install the engine service hole cover No.2 with the 3 bolts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }
    2. A003CDS

      Return the carpet.

  10. CHECK FUNCTION OF THROTTLE BODY

    Click here

  11. INSTALL ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

    Torque:
    13 Н*м  { 133 кгс*см, 10 фунт-сила-футов }