КАТАЛИТИЧЕСКИЙ НЕЙТРАЛИЗАТОР В ВЫПУСКНОМ КОЛЛЕКТОРЕ СНЯТИЕ


  1. REMOVE ENGINE ASSEMBLY

    Click here

  2. REMOVE DIFFERENTIAL PRESSURE SENSOR


    1. A003GPH

      Disconnect the connector from the differential pressure sensor.

    2. Remove the bolt and differential pressure sensor from the pipe clamp.

    3. A003B3B

      Slide the 2 clamps and disconnect the 2 air hoses from the No. 1 vacuum pipe and No. 2 vacuum pipe.

    4. A003HRH

      Slide the 2 clamps and remove the 2 air hoses from the differential pressure sensor.

  3. REMOVE EXHAUST GAS TEMPERATURE SENSOR

    CAUTION:

    To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


    1. A003CY1

      Disconnect the 3 connectors from the 3 exhaust gas temperature sensors.

    2. A003GZI

      Remove the nut and disconnect the No. 3 exhaust gas temperature sensor from the No. 1 vacuum pipe.

    3. A003ENE

      Remove the bolt and open the clamp of the pipe clamp.

    4. Detach the 3 connectors from the pipe clamp.

    5. A003CZ4

      Using a 14 mm union nut wrench, remove the exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.

    6. A003AL6

      Using a 14 mm union nut wrench, remove the No. 2 exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.

    7. A003DXU

      Using a 14 mm union nut wrench, remove the No. 3 exhaust gas temperature sensor from the exhaust manifold converter sub-assembly.

  4. REMOVE NO. 1 VACUUM PIPE


    1. A003AYH

      Remove the nut and clamp from the No. 1 vacuum pipe and No. 2 vacuum pipe.

    2. A003DAU

      Using a 17 mm union nut wrench, remove the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.

  5. REMOVE NO. 2 VACUUM PIPE


    1. A003HV7

      Using a 17 mm union nut wrench, remove the No. 2 vacuum pipe from the exhaust manifold converter sub-assembly.

    2. A003GRS

      Remove the clamp from the pipe clamp.

  6. REMOVE PIPE CLAMP


    1. A003GK1

      Remove the 3 bolts and pipe clamp from the engine cover bracket.

  7. REMOVE ENGINE COVER BRACKET


    1. A003GKG

      Detach the 2 clamp and disconnect the engine wire from the engine cover bracket.

    2. A003H9B

      Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.

  8. REMOVE AIR FUEL RATIO SENSOR

    CAUTION:

    To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


    1. A003ELUE01

      Disconnect the connector.

    2. Using SST, remove the air fuel ratio sensor.

      SST
      09224-00012

  9. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. A003B34

      Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.

  10. REMOVE NO. 1 TURBO INSULATOR


    1. A003G8Y

      Remove the 3 bolts and No. 1 turbo insulator from the exhaust manifold and turbocharger sub-assembly.

  11. REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY


    1. A003IBQ

      Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.

  12. REMOVE EXHAUST PIPE SUPPORT STAY


    1. A003DEU

      Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.

  13. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    1. A003EH3

      Remove the nut, exhaust pipe clamp and exhaust manifold converter sub-assembly from the turbocharger sub-assembly.

    2. Remove the gasket.