ТОПЛИВНЫЙ БАК СНЯТИЕ


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE PROPELLER SHAFT ASSEMBLY

    Click here

  5. DISCONNECT FUEL TANK WIRE


    1. A003CJUE01

      Disconnect the fuel tank wire connector.

  6. DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A003FW5E01

      Disconnect the No. 1 fuel evaporation tube sub-assembly Click here.

  7. DISCONNECT FUEL TANK RETURN TUBE


    1. A003GWGE01

      Disconnect the fuel tank return tube Click here.

  8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A003EDX

      Disconnect the fuel tank main tube sub-assembly Click here.

  9. DISCONNECT FUEL TANK BREATHER HOSE


    1. A003F7ME01

      Slide the clamp and disconnect the fuel tank breather hose from the fuel tank assembly.

  10. REMOVE FUEL HOSE PROTECTOR


    1. A003DY4

      Detach the 2 claws to remove the fuel hose protector from the fuel tank to filler pipe hose.

  11. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    1. A003GU6E01

      Loosen the hose clamp to disconnect the fuel tank to filler pipe hose from the fuel tank inlet pipe sub-assembly.

  12. REMOVE FUEL TANK ASSEMBLY


    1. Remove the bolt and disconnect the No. 3 parking brake cable assembly.

    2. Hold the fuel tank assembly using an engine lifter.

    3. A003AXKE01

      Remove the 6 bolts, No. 1 fuel tank band sub-assembly RH and No. 1 fuel tank band sub-assembly LH.

    4. Operate the engine lifter, and then remove the fuel tank assembly.

  13. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A003BDFE01

      Disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction with pump and gauge tube assembly Click here.

  14. REMOVE FUEL TANK RETURN TUBE


    1. A003EBCE01
      Text in Illustration
      *1 Fuel Tube Joint
      *2 Fuel Tube
      *3 O-Ring
      *4 Tube Joint Clip

      Remove the tube joint clip and pull the fuel tank return tube out of the plug of the fuel suction with pump and gauge tube assembly.

      Note

      A003HQME18

      • Remove any dirt and foreign matter on the fuel tube joint before performing this step.

      • Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube joint contains the O-rings that seal the plug.

      • Perform this step by hand. Do not use any tools.

      • Do not forcibly bend or twist the nylon tube.

      • Protect the disconnected parts by covering them with plastic bags and tape after disconnecting the fuel tubes.

  15. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A003D9FE01
      Text in Illustration
      *1 Fuel Tube Joint
      *2 Fuel Tube
      *3 O-Ring
      *4 Tube Joint Clip

      Remove the tube joint clip and pull the fuel tank main tube sub-assembly out of the plug of the fuel suction with pump and gauge tube assembly.

      Note

      A003HQME18

      • Remove any dirt and foreign matter on the fuel tube joint before performing this step.

      • Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube joint contains the O-rings that seal the plug.

      • Perform this step by hand. Do not use any tools.

      • Do not forcibly bend or twist the nylon tube.

      • Protect the disconnected parts by covering them with plastic bags and tape after disconnecting the fuel tubes.

  16. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    1. A003BSME01

      Disconnect the fuel tank wire connector.

    2. A003C9ZE01

      Press down on the fuel suction with pump and gauge tube assembly and remove the 8 bolts and fuel tank vent tube set plate.

      Note


      • When the fuel tank vent tube set plate is removed, be careful as the fuel suction with pump and gauge tube assembly will spring upward from the force of the spring.

      • Remove any foreign matter around the fuel suction with pump and gauge tube assembly before this operation.

    3. Remove the fuel suction with pump and gauge tube assembly from the fuel tank assembly.

      Note

      Be careful not to bend the arm of the fuel sender gauge assembly.

    4. Remove the fuel suction tube set gasket from the fuel tank assembly.

  17. REMOVE FUEL HOSE GROMMET


    1. Remove the fuel hose grommet from the fuel tank assembly.