Click here

ЗАДНИЙ САЛЬНИК КОЛЕНЧАТОГО ВАЛА УСТАНОВКА

Click here
Click here Click here
  1. Click here

    INSTALL ENGINE REAR OIL SEAL


    1. A003D6FE01

      Using SST and a hammer, tap in a new oil seal.

      09518-36030
      09950-70010 09951-07200
      Acceptable depth from the top flat face of the oil seal retainer
      0 to 0.5 mm (0 to 0.020 in.)
      Note:

      Be sure to make the oil seal horizontal when embedded.

    2. Apply a bit of MP grease to the oil seal's lip.

      Note:

      Keep the lip clean. Do not bring dirt or dusts on that area.

  2. Click here

    INSTALL ENGINE REAR OIL SEAL RETAINER


    1. A003ANVE02

      Remove oil seal packing (FIPG) from oil pan and cylinder block.

    2. Apply a seal packing to the specific places described in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Note:

      • After applying FIPG install the engine rear oil seal retainer within 3 minutes and then tighten its bolts within 15 minutes.

      • Do not start the engine 2 hours after the installation.

    3. A003AY9E01

      Install the engine rear oil seal retainer with the 7 bolts.

      Bolt A
      13 N*m 133 kgf*cm 10 ft.*lbf
      Bolt B
      16 N*m 166 kgf*cm 12 ft.*lbf
  3. Click here

    INSTALL REAR END PLATE


    1. Установите заднюю крышку и закрепите ее болтом.

      8,0 Н*м 82 кгс*см 71 фунт-сила-дюйм
  4. Click here

    INSTALL FLYWHEEL SUB-ASSEMBLY


    1. A003FDJE01

      С помощью SST зафиксируйте коленчатый вал.

      09213-58013
      09330-00021
    2. A003BGDE02

      Нанесите герметик на два или три витка резьбы 8 болтов.

      Герметик
      Фирменный герметик 1344 от компании Toyota, Three Bond 1344 или аналогичный
    3. A003AKXE01

      Для моделей с механической трансмиссией


      1. Установите маховик и закрепите его 8 болтами.

        178 Н*м 1 815 кгс*см 131 фунт-сила-фут

    4. Для моделей с автоматической трансмиссией.


      1. Установите маховик, ведущий диск и заднюю распорную втулку ведущего диска и закрепите их 8 болтами.

        178 Н*м 1 815 кгс*см 131 фунт-сила-фут
  5. Click here

    INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)


    1. A003DDKE01

      Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

      09301-00110
      Note:

      Take care not to insert the clutch disc assembly in the wrong direction.

  6. Click here

    INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)


    1. A003H0AE02

      Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.

    2. Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.

      09301-00110
      19 N*m 195 kgf*cm 14 ft.*lbf
      Tip:

      • Evenly tighten the bolts by following the order shown in the illustration.

      • Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.

  7. Click here

    INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)


    1. A003G6I

      Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

      Maximum non-alignment
      1.3 mm (0.051 in.)
    2. A003CZWE01

      If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

      09333-00013
  8. Click here

    INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

    (Click here)

  9. Click here

    INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

    (Click here)