Click here

СИСТЕМА SFI, Diagnostic DTC:P060E

Click here
Click here
DTC Code DTC Name
P060E Internal Control Module Throttle Position Performance
Click here

DESCRIPTION

The ECM monitors the input signals of the throttle position sensor No. 1 and stop light switch. If the input signals and control signals deviate, a DTC is stored.

DTC No. DTC Detection Condition Trouble Area
P060E

Either condition is met (1 trip detection logic):


  • There is an ECM main CPU error.

  • There is an ECM sub CPU error.

 ECM
Click here

MONITOR STRATEGY

Required sensors/Components ECM
Frequency of operation Once per driving cycle
Click here

TYPICAL ENABLING CONDITIONS

DMA communication error Not detected
Click here

TYPICAL MALFUNCTION THRESHOLDS

When one of following conditions is met: Condition 1 or 2
1. Difference of main throttle position and sub throttle position 0.3 V or more
2. Stop light switch signal (CPU) and stop light switch signal (Monitor IC) Different
Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON and turn the intelligent tester on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

  4. Turn the intelligent tester off.

  5. Turn the ignition switch off.

  6. Disconnect the intelligent tester.

  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  8. Connect the cable to the negative (-) battery terminal.

  9. Connect the intelligent tester to the DLC3.

  10. Turn the ignition switch to ON and turn the intelligent tester on.

  11. Wait 16 seconds or more.

  12. Enter the following menus: Powertrain / Engine and ECT / DTC.

  13. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  15. Input the DTC: P060E.

  16. Check the DTC judgment result.

    Tester Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    Tip:

    • If a permanent DTC is output, the system is malfunctioning.

    • If no permanent DTC is output, the system is normal.

Click here

INSPECTION PROCEDURE

Note:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

Tip:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    CHECK FOR DTC


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Clear the DTCs (Click here).

    5. Turn the intelligent tester off.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester.

    8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

    9. Connect the cable to the negative (-) battery terminal.

    10. Connect the intelligent tester to the DLC3.

    11. Turn the ignition switch to ON and turn the intelligent tester on.

    12. Wait 16 seconds or more.

    13. Enter the following menus: Powertrain / Engine and ECT / DTC.

    14. Check for DTCs.

      OK
      P060E is not output.

  2. Click here

    CHECK FOR INTERMITTENT PROBLEMSClick here

  3. Click here

    REPLACE ECMClick here