Click here

СИСТЕМА ECD, Diagnostic DTC:P0724

Click here
Click here
DTC Code DTC Name
P0724 Brake Switch "B" Circuit High
Click here

DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

Table 1. P0724
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times. Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times (2 trip detection logic).

  • Short in stop light switch signal circuit

  • Stop light switch assembly

  • ECM
Table 2. Related Data List
DTC No. Data List
P0724 Stop Light Switch
Click here

WIRING DIAGRAM

Refer to DTC P0504 (Click here).

Click here

INSPECTION PROCEDURE

Note:

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

  • After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).

  • After replacing an injector assembly, the ECM needs registration (Click here).

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (STOP LIGHT SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

    4. Read the value displayed on the GTS when the brake pedal is depressed and released.

      OK
      Brake Pedal Display
      Released OFF
      Depressed ON

  2. Click here

    INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly (Click here).


  3. Click here

    CHECK ECM (STP VOLTAGE)


    1. Disconnect the ECM connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Brake Pedal Condition Specified Condition
      B88-35 (STP) - Body ground Released 0 to 1.5 V
      Depressed 11 to 14 V
      Table 3. Text in Illustration
      *a Brake Pedal Depressed
      *b Brake Pedal Released
      *c

      Front view of wire harness connector

      (to ECM)

  4. Click here

    REPLACE ECM


    1. Replace the ECM (Click here).


  5. Click here

    REPLACE STOP LIGHT SWITCH ASSEMBLY


    1. Replace the stop light switch assembly.


  6. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


  7. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs (Click here).

    3. Turn the ignition switch off for 30 seconds or more.

    4. Turn the ignition switch to ON and turn the GTS on.

    5. Start the engine.

    6. Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.

    7. Confirm that the DTC is not output again.

      Tip:

      Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


      1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

      2. Input DTC P0724.

      3. Check that STATUS is NORMAL.

        Tip:

        • If STATUS is NORMAL, DTC judgment is complete and it can be determined that the system is normal.

        • If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.


  8. Click here

    END