Click here

СИСТЕМА ECD, Diagnostic DTC:P2080, P2084, P242B

Click here
Click here
DTC Code DTC Name
P2080 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2
P242B Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3
Click here

DESCRIPTION

Refer to DTC P0545 (Click here).

Table 1. P2080
DTC Detection Drive Pattern DTC Detection Condition Trouble Area

Check the exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving*

*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.

The change in the exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.

(2 trip detection logic)

  • Exhaust gas temperature sensor

  • ECM (soak timer)
Table 2. P2084
DTC Detection Drive Pattern DTC Detection Condition Trouble Area

Check the No. 2 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving*

*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.

The change in the No. 2 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.

(2 trip detection logic)

  • No. 2 Exhaust gas temperature sensor

  • ECM (soak timer)
Table 3. P242B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area

Check the No. 3 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving*

*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.

The change in the No. 3 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.

(2 trip detection logic)

  • No. 3 Exhaust gas temperature sensor

  • ECM (soak timer)
Table 4. Related Data List
DTC No. Data List

P2080

P2084

P242B

  • Exhaust Temperature B1S1

  • Exhaust Temperature B1S2

  • Exhaust Temperature B1S3
Tip:

  • Sensor 1 represents the sensor located upstream of the DOC catalytic converter.

  • Sensor 2 represents the sensor located upstream of the DPF catalytic converter.

  • Sensor 3 represents the sensor located downstream of the DPF catalytic converter.

  • If DTC P2080, P2084 or P242B is stored, the following symptoms may appear:


    • White smoke

Click here

WIRING DIAGRAM

Refer to DTC P0545 (Click here).

Click here

INSPECTION PROCEDURE

Note:

After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2080, P2084 OR P242B)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Read DTCs.

      Table 5. Result
      Result Proceed to
      DTC P2080, P2084 or P242B is output A
      DTC P2080, P2084 or P242B and other DTCs are output B

  2. Click here

    READ VALUE USING GTS (EXHAUST TEMPERATURE)


    1. Leave the vehicle as is for 1 to 2 hours with the engine stopped.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

    5. Record the exhaust temperature displayed on the GTS.


  3. Click here

    INSPECT EXHAUST GAS TEMPERATURE SENSOR


    1. Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.

    2. Stop the vehicle.

    3. Connect the GTS to the DLC3.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

    5. Read the value.

      Result
      Result Proceed to
      Difference between Exhaust Temperature B1S1 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S1 checked after driving is within +/-15°C (27°F) A
      Difference between Exhaust Temperature B1S2 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S2 checked after driving is within +/-15°C (27°F)
      Difference between Exhaust Temperature B1S3 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S3 checked after driving is within +/-15°C (27°F)
      Difference between exhaust temperature recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and exhaust temperature checked after driving is equal to or greater than +/- 15°C (27°F) B

  4. Click here

    REPLACE EXHAUST GAS TEMPERATURE SENSOR

    Tip:

    Replace the exhaust temperature sensor that changed a small amount in "INSPECT EXHAUST GAS TEMPERATURE SENSOR".


    1. Replace the exhaust gas temperature sensor (Click here).

    2. Replace the No. 2 exhaust gas temperature sensor (Click here).

    3. Replace the No. 3 exhaust gas temperature sensor (Click here).


  5. Click here

    REPLACE ECM


    1. Replace the ECM (Click here).


  6. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Leave the vehicle as is for 1 to 2 hours with the engine stopped.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

    5. Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.

    6. Stop the vehicle.

    7. Connect the GTS to the DLC3.

    8. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

    9. Check the exhaust temperature after leaving the vehicle for 1 to 2 hours and after driving.

      Standard
      +/-15°C(27°F) or more

  7. Click here

    GO TO DTC CHARTClick here

  8. Click here

    END