METER / GAUGE SYSTEM ON-VEHICLE INSPECTION


  1. CHECK INDICATOR/WARNING LIGHT


    1. Check the following indicators and warning lights.

      Indicator/Warning Light Switch Condition Switch Condition
      ABS warning light*9 Ignition switch off → ON Comes on for 3 seconds
      BRAKE warning light
      T-BELT warning light*1
      Eco driving indicator light*2
      Headlight beam level control system indicator light*3, *4
      DPF indicator light*5
      Brake override system warning light
      LED headlight warning light*3, *4
      Slip indicator light*7
      VSC OFF indicator light*7
      Tire pressure warning light*11
      TRC OFF indicator light*7
      AIRBAG warning light*6 Ignition switch off → ON Comes on for 6 seconds
      MIL warning light*10 Ignition switch off → ON

      • Illuminates when ignition switch turned ON

      • Turns off when engine started
      CHARGE warning light
      OIL warning light*8

      • *1: Engine Type Diesel

      • *2: for Automatic Transmission

      • *3: for LED Headlight

      • *4: for Segment Display Type

      • *5: for 1KD-FTV (w/ DPF)

      • *6: w/ Airbag System

      • *7: w/ VSC

      • *8: except 1KD-FTV (w/ DPF)

      • *9: w/ ABS

      • *10: for Dot Display Type

      • *11: w/ Tire Pressure Warning System

  2. CHECK SPEEDOMETER


    1. Using a speedometer tester, check the speedometer indication according to the table below.

      for mph
      Standard Indication Acceptable Range
      20 21.0 to 23.5
      40 42.0 to 44.5
      60 62.5 to 66.0
      80 83.1 to 87.1
      100 103.9 to 108.4
      for km/h (except Australia)
      Standard Indication Acceptable Range
      20 21.0 to 25.0
      40 41.7 to 46.2
      60 62.7 to 67.2
      80 83.4 to 88.4
      100 104.3 to 109.3
      120 125.1 to 130.6
      140 145.8 to 151.8
      160 166.2 to 173.2
      for km/h (except 1KD-FTV, Manual Transmission [for Australia])
      Standard Indication Acceptable Range
      20 20.4 to 24.4
      40 41.0 to 45.5
      60 61.4 to 65.9
      80 82.0 to 87.0
      100 10.24 to 107.4
      120 122.8 to 128.3
      140 143.4 to 149.4
      160 163.8 to 170.3
      for km/h (for 1KD-FTV, Manual Transmission [for Australia])
      Standard Indication Acceptable Range
      20 20.6 to 24.6
      40 41.3 to 45.8
      60 61.9 to 66.4
      80 82.6 to 87.6
      100 103.2 to 107.7
      120 123.9 to 128.9
      140 144.5 to 149.5
      160 165.2 to 170.2
      for km/h (for Automatic Transmission [for Australia])
      Standard Indication Acceptable Range
      20 20.1 to 24.1
      40 40.2 to 44.7
      60 60.4 to 64.9
      80 80.5 to 85.5
      100 100.6 to 105.6
      120 120.7 to 126.2
      140 140.9 to 146.9
      160 160.9 to 167.4

      Note

      Do not use worn, underinflated or overinflated tires as the speedometer reading will be inaccurate.

    2. Check the deflection width of the speedometer indicator.

      Reference
      Below 0.5 km/h (0.3 mph)

  3. CHECK TACHOMETER (w/ Tachometer)


    1. Connect a tune-up test tachometer, and start the engine.

    2. Compare the test results and the tachometer indications.

      DC 13.5 V at 25°C (77°F)
      Standard Indication (rpm)

      Acceptable Range

      Data in ( ) is for Reference
      700 630 to 770
      1,000 (900 to 1,100)
      2,000 (1,850 to 2,150)
      3,000 2,800 to 3,200
      4,000 (3,800 to 4,200)
      5,000 4,800 to 5,200
      6,000 (5,750 to 6,250)

  4. CHECK METER/GAUGE


    1. Connect the GTS to the DLC3.

    2. Perform the Active Test Click here.

      OK
      Each meter/gauge needle indication is normal.

  5. CHECK WARNING/INDICATOR LIGHT


    1. Connect the GTS to the DLC3.

    2. Perform the Active Test Click here.

      OK
      Each warning/indicator light can be turned on and off using the GTS.

  6. CHECK MULTI-INFORMATION DISPLAY (Dot Display Type)


    1. Connect the GTS to the DLC3.

    2. Perform the Active Test Click here.

      OK
      All dots in the multi-information display can be turned on and off using the GTS.