OUTPUT SHAFT INSPECTION


  1. INSPECT 1ST GEAR THRUST CLEARANCE


    1. A003HB5

      Using a dial indicator, measure the thrust clearance of the 1st gear.

      Standard clearance
      0.30 to 0.55 mm (0.0118 to 0.0216 in.)

  2. INSPECT 2ND GEAR THRUST CLEARANCE


    1. A003ICDE11

      Using a dial indicator, measure the thrust clearance of the 2nd gear.

      Standard clearance
      0.10 to 0.25 mm (0.0039 to 0.0098 in.)

  3. INSPECT 3RD GEAR THRUST CLEARANCE


    1. A003IC1E02

      Using a feeler gauge, measure the thrust clearance of the 3rd gear.

      Standard clearance
      0.10 to 0.25 mm (0.0039 to 0.0098 in.)

  4. INSPECT 1ST GEAR RADIAL CLEARANCE


    1. A003D29

      Using a dial indicator, measure the radial clearance of the 1st gear.

      Standard clearance
      0.020 to 0.073 mm (0.0008 to 0.0029 in.)

      If the clearance is not within the specified values, replace the 1st gear needle roller bearing with a new one.

  5. INSPECT 2ND GEAR RADIAL CLEARANCE


    1. A003DSD

      Using a dial indicator, measure the radial clearance of the 2nd gear.

      Standard clearance
      0.015 to 0.068mm (0.0006 to 0.0027 in.)

      If the clearance is not within the specified values, replace the 2nd gear needle roller bearing with a new one.

  6. INSPECT 3RD GEAR RADIAL CLEARANCE


    1. A003I8C

      Using a dial indicator, measure the radial clearance of the 3rd gear.

      Standard clearance
      0.015 to 0.068 mm (0.0006 to 0.0027 in.)

      If the clearance is not within the specified values, replace the 3rd gear needle roller bearing with a new one.

  7. INSPECT OUTPUT SHAFT


    1. A003GF1

      Using a dial indicator, measure the runout of the output shaft.

      Maximum runout
      0.03 mm (0.0012 in.)

      If the runout is greater than the maximum, replace the output shaft with a new one.

    2. A003CDAE01

      Using a micrometer, measure the outer diameter of the output shaft at points A, B and C.

      Standard diameter
      38.979 to 38.995 mm (1.5334 to 1.5352 in.) for A
      46.984 to 47.000 mm (1.8498 to 1.8504 in.) for B
      37.984 to 38.000 mm (1.4954 to 1.4961 in.) for C
      Minimum diameter
      38.979 mm (1.5334 in.) for A
      46.984 mm (1.8498 in.) for B
      37.984 mm (1.4954 in.) for C

      If the outer diameter is less than the minimum, replace the output shaft with a new one.

    3. A003GDU

      Using a micrometer, measure the thickness of the output shaft flange as shown in the illustration.

      Standard thickness
      4.8 to 5.2 mm (0.1890 to 0.2047 in.)

      If the thickness is not within the specified values, replace the output shaft.

  8. INSPECT 3RD GEAR


    1. A003CSN

      Using a cylinder gauge, measure the inner diameter of the 3rd gear.

      Standard diameter
      44.015 to 44.040 mm (1.7329 to 1.7339 in.)
      Maximum diameter
      44.040 mm (1.7339 in.)

      If the inner diameter is greater than the maximum, replace the 3rd gear with a new one.

  9. INSPECT 2ND GEAR


    1. A003E4I

      Using a cylinder gauge, measure the inner diameter of the 2nd gear.

      Standard diameter
      53.015 to 53.040 mm (2.0872 to 2.0881 in.)
      Maximum diameter
      53.040 mm (2.0881 in.)

      If the inner diameter is greater than the maximum, replace the 2nd gear with a new one.

  10. INSPECT 1ST GEAR


    1. A003C3W

      Using a cylinder gauge, measure the inner diameter of the 1st gear.

      Standard diameter
      46.015 to 46.040 mm (1.812 to 1.813 in.)
      Maximum diameter
      46.040 mm (1.8126 in.)

      If the inner diameter is greater than the maximum, replace the 1st gear with a new one.

  11. INSPECT 1ST GEAR THRUST WASHER


    1. A003E20

      Using a micrometer, measure the thickness of the 1st gear thrust washer.

      Standard thickness
      5.95 to 6.05 mm (0.2346 to 0.2382 in.)
      Minimum thickness
      5.96 mm (0.2346 in.)

      If the thickness is less than the minimum, replace the 1st gear thrust washer.

  12. INSPECT SYNCHRONIZER RING NO.1 (for 1st Gear (2TR-FE))


    1. A003GSW

      Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring No.1 (for the first synchronizer ring).

      If it turns, replace the synchronizer ring No.1.

    2. A003FKG

      Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.

      Standard clearance
      0.75 to 1.65 mm (0.0295 to 0.0649 in.)

      If the clearance is not within the specified values, replace the synchronizer ring No.1 with a new one.

  13. INSPECT SYNCHRONIZER RING SET NO.1 (for 1st Gear (2KD-FTV))


    1. A003G5X

      Apply gear oil to the cone of the 1st gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the first synchronizer ring).

      If it turns, replace the synchronizer ring set No.1.

    2. A003H2U

      Measure the clearance between the synchronizer ring No.1 and 1st gear while pushing the synchronizer ring No.1 against the cone of the 1st gear.

      Standard clearance
      0.65 to 1.75 mm (0.0256 to 0.0689 in.)

      If the clearance is not within the specified values, replace the synchronizer ring No.1 with a new one.

  14. INSPECT SYNCHRONIZER RING SET NO.1 (for 2nd Gear)


    1. A003ATS

      Apply gear oil to the cone of the 2nd gear, and check that it does not turn in either direction while pushing the synchronizer ring set No.1 (for the second synchronizer ring).

      If it turns, replace the synchronizer ring set No.1.

    2. A003C7X

      Measure the clearance between the synchronizer ring set No.1 (for the second synchronizer ring) and 2nd gear while pushing the synchronizer ring set No.1 against the cone of the 2nd gear.

      Standard clearance
      0.65 to 1.75 mm (0.0256 to 0.0689 in.)

      If the clearance is not within the specified values, replace the synchronizer ring set No.1 (for the second synchronizer ring) with a new one.

  15. INSPECT SYNCHRONIZER RING NO.2 (for 3rd Gear)


    1. A003HGK

      Apply gear oil to the cone of the 3rd gear, and check that it does not turn in either direction while pushing the synchronizer ring No.2 (for the third synchronizer ring).

      If it turns, replace the synchronizer ring No.2.

    2. A003EIN

      Measure the clearance between the synchronizer ring No.2 (for the third synchronizer ring) and 3rd gear while pushing the synchronizer ring No.2 (for the second synchronizer ring) against the cone of the 3rd gear.

      Standard clearance
      0.75 to 1.65 mm (0.0295 to 0.0650 in.)

      If the clearance is not within the specified values, replace the synchronizer ring No.2 (for the third synchronizer ring) with a new one.

  16. INSPECT REVERSE GEAR


    1. A003AU6E02

      Using vernier calipers, measure the width of the reverse gear groove and the thickness of the claw part on the gear shift fork No.1, and calculate the clearance.

      Standard clearance (A - B)
      0.15 to 0.41 mm (0.0060 to 0.0161 in.)

      If the clearance is not within the specified values, replace the reverse gear and the shift fork No.1 with new ones.

  17. INSPECT TRANSMISSION CLUTCH HUB NO.1


    1. A003FIZ

      Check that the transmission clutch hub No.1 and reverse gear slide smoothly each other.

    2. Check the tip of the spline gear sleeve of the reverse gear for wear.

      If there are any defects, replace the transmission clutch hub No.1.

  18. INSPECT TRANSMISSION HUB SLEEVE NO.2


    1. A003DCHE02

      Using vernier calipers, measure the width of the transmission hub No.2 groove and the thickness of the claw of the gear shift fork No.2.

      Standard clearance (A - B)
      0.15 to 0.35 mm (0.0059 to 0.0138 in.)

      If the clearance is not within the specified values, replace the transmission hub sleeve No.2 and the shift fork No.2 with new ones.

  19. INSPECT TRANSMISSION CLUTCH HUB NO.2


    1. A003EHM

      Check the sliding condition between the transmission clutch hub No.2 and the transmission hub sleeve No.2.

    2. Check the tip of the spline gear sleeve of the reverse gear for wear.