SMART ENTRY AND START SYSTEM (for Start Function), Diagnostic DTC:B2274

DTC Code DTC Name
B2274 ACC Monitor Malfunction

DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

Tech Tips

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2274

Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).

Tech Tips

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.

  • AM2 fuse

  • No. 2 Integration Relay (ACC relay)

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

 Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected

  • If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

  • If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).

Tech Tips

The engine switch can be turned on (IG) and the engine can be started.

 -
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274

    Power Source Control

  • ACC Relay Monitor


    Starting Control

  • Ignition

 -

WIRING DIAGRAM

A003E4EE01

INSPECTION PROCEDURE

Note


  • When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution Click here.

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      A003H7QE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      B75-1 (+B) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

    OK

  2. CHECK HARNESS AND CONNECTOR (GROUND)


    1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      A003H7QE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      B75-10 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY)


    1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the 12E No. 2 integration relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B75-21 (ACCD) - 12E-8 Always Below 1 Ω
      12E-4 - Body ground
      B75-21 (ACCD) or 12E-8 - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK NO. 2 INTEGRATION RELAY (ACC RELAY)


    1. Remove the No. 2 integration relay.

      A003BLIE01
      Text in Illustration
      *a

      Component without harness connected

      (No. 2 Integration Relay)

      		 - -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      12E-7 - 12E-9 Battery voltage not applied to terminals 12E-8 and 12E-4 10 kΩ or higher
      Battery voltage applied to terminals 12E-8 and 12E-4 Below 1 Ω

    NG

    REPLACE NO. 2 INTEGRATION RELAY

    OK

  5. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. Reconnect the B75 certification ECU (smart key ECU assembly) connector.

    2. Install the No. 2 integration relay.

    3. Measure the voltage according to the value(s) in the table below.

      A003HSFE02
      Text in Illustration
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      B75-21 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    USE SIMULATION METHOD TO CHECK Click here