ROOF HEADLINING (for Full-trim) INSTALLATION


  1. INSTALL ROOF HEADLINING NO. 1 (for High Roof)

  2. INSTALL ROOF HEADLINING NO. 1 (for Middle Roof)

  3. INSTALL REAR COOLER CONTROL PANEL

  4. INSTALL MAP LIGHT ASSEMBLY (Super Wagon)

  5. INSTALL ROOM LIGHT ASSEMBLY NO. 1 (Deluxe)

  6. INSTALL VISOR HOLDER

  7. INSTALL VISOR ASSEMBLY LH

  8. INSTALL VISOR ASSEMBLY RH

  9. INSTALL ASSIST GRIP

  10. INSTALL FRONT PILLAR GARNISH RH

  11. INSTALL FRONT PILLAR GARNISH LH

  12. INSTALL ASSIST GRIP ASSEMBLY

  13. INSTALL FRONT ASSIST GRIP PLUG NO. 1

  14. INSTALL ROOF HEADLINING NO. 2 (for High Roof)

  15. INSTALL ROOF HEADLINING NO. 2 (for Middle Roof)

  16. INSTALL REAR ROOF HEADLINING GARNISH (w/ Roof Window Glass)

  17. INSTALL ROOM LIGHT ASSEMBLY NO. 2 (Super Wagon)

  18. INSTALL ROOM LIGHT ASSEMBLY NO. 2 (Deluxe)

  19. INSTALL REAR SEAT HOOK (for Space Up Seat)

  20. INSTALL ROOF SIDE GARNISH INNER UPPER RH

  21. INSTALL ROOF SIDE GARNISH INNER UPPER LH

  22. INSTALL QUARTER PILLAR GARNISH RH (for Middle Roof)

  23. INSTALL QUARTER PILLAR GARNISH LH (for Middle Roof)

  24. INSTALL QUARTER PILLAR GARNISH RH (for High Roof)

  25. INSTALL QUARTER PILLAR GARNISH LH (for High Roof)

  26. INSTALL CENTER PILLAR GARNISH RH

  27. INSTALL CENTER PILLAR GARNISH LOWER RH

  28. INSTALL ASSIST GRIP ASSEMBLY REAR

  29. INSTALL ASSIST GRIP PLUG

  30. INSTALL CENTER PILLAR GARNISH LH

  31. INSTALL ENGINE SERVICE HOLE COVER HOOK NO. 2 LH

  32. INSTALL SIDE NO. 1 TRIM ASSEMBLY LH

  33. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR RH

  34. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (for High Roof)

  35. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (for Middle Roof)

  36. INSTALL BACK DOOR WEATHERSTRIP

  37. INSTALL BACK DOOR SCUFF PLATE

  38. INSTALL SLIDE DOOR WEATHERSTRIP NO. 1 RH

  39. INSTALL REAR DOOR SCUFF PLATE RH

  40. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A003GYM

      Connect the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A003GG5

      Attach the 2 claws to close the cover.

    3. A003FKR

      Connect the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  41. INSTALL SEAT BELT ANCHOR COVER

  42. INSTALL SEAT ASSEMBLY LH

  43. INSTALL CENTER PILLAR GARNISH COVER LOWER LH

  44. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH


    1. A003C9J

      Connect the front seat outer belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A003EIR

      Attach the 2 claws to close the cover.

    3. A003E32

      Connect the front seat outer belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  45. INSTALL FRONT DOOR OPENING TRIM RH

  46. INSTALL FRONT DOOR OPENING TRIM LH

  47. INSTALL FRONT DOOR SCUFF PLATE RH

  48. INSTALL FRONT DOOR SCUFF PLATE LH

  49. INSTALL REAR NO. 4 SEAT BELT ASSEMBLY OUTER


    1. A003D2CE01
      Text in Illustration
      *a Unlocked
      *b Locked
      *c 45°

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

        If operation is not as specified, replace the rear No. 4 seat belt assembly outer.

    2. A003BNU

      Install the rear No. 4 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A003HLE

      Attach the 4 claws to install the retractor cover of the rear No. 4 seat belt assembly outer.

    4. A003E9N

      Connect the shoulder side of the rear No. 4 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. A003AMA

      Attach the 2 claws to close the shoulder side cover of the rear No. 4 seat belt assembly outer.

    6. A003DY3

      Connect the floor side of the rear No. 4 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Check if the ELR locks.

      Note

      This check should be performed with the rear No. 4 seat belt assembly outer installed.


      1. With the rear No. 4 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the rear No. 4 seat belt assembly outer.

  50. INSTALL REAR NO. 3 SEAT BELT ASSEMBLY OUTER


    1. A003BC5E01
      Text in Illustration
      *a Unlocked
      *b Locked
      *c 45°

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

        If operation is not as specified, replace the rear No. 3 seat belt assembly outer.

    2. A003EXK

      Install the rear No. 3 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A003HU9

      Attach the 4 claws to install the retractor cover of the rear No. 3 seat belt assembly outer.

    4. A003AT9

      Tighten the bolt to connect the shoulder side of the rear No. 3 seat belt assembly outer.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. A003DWG

      Attach the 4 claws to close the shoulder side cover of the rear No. 3 seat belt assembly outer.

    6. A003FYN

      Connect the floor side of the rear No. 3 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Check if the ELR locks.

      Note

      This check should be performed with the rear No. 3 seat belt assembly outer installed.


      1. With the rear No. 3 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the rear No. 3 seat belt assembly outer.

  51. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY OUTER


    1. A003DY1E01
      Text in Illustration
      *a Unlocked
      *b Locked
      *c 45°

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

        If operation is not as specified, replace the rear No. 2 seat belt assembly outer.

    2. A003F50

      Install the rear No. 2 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A003BCD

      Connect the shoulder side of the rear No. 2 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. A003BCB

      Attach the 2 claws to close the shoulder side cover of the rear No. 2 seat belt assembly outer.

    5. A003EN6

      Connect the floor side of the rear No. 2 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. Check if the ELR locks.

      Note

      This check should be performed with the rear No. 2 seat belt assembly outer installed.


      1. With the rear No. 2 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the rear No. 2 seat belt assembly outer.

  52. INSTALL REAR SEAT BELT ASSEMBLY OUTER


    1. A003GO1E01
      Text in Illustration
      *a Unlocked
      *b Locked
      *c 45°

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

        If operation is not as specified, replace the rear seat belt assembly outer.

    2. A003DK3

      Tighten the bolt to install the rear seat belt assembly outer.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A003F3T

      Tighten the bolt to connect the shoulder side of the rear seat belt assembly outer.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. A003CYM

      Attach the 4 claws to close the shoulder side cover of the rear seat belt assembly outer.

    5. A003B6B

      Connect the floor side of the rear seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. for Rear No. 1 Seat Bench Seat Type:


      1. A003BNJE01
        Text in Illustration
        *a Unlocked
        *b Locked
        *c 45°

        Check the degree of tilt when the ELR begins to lock.

        Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

        If operation is not as specified, replace the rear seat belt assembly outer.

      2. w/ Cover:


        1. Install the side trim cover to the rear seat belt assembly outer.

        2. Install the bolt to the floor side of the rear seat belt assembly outer.

      3. A003H4Y

        Temporarily install the rear seat belt assembly outer with the 2 bolts.

      4. Tighten the lower side bolt first, and then tighten the upper side bolt to install the rear seat belt assembly outer.

        Torque:
        for Upper Bolt
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
        for Lower Bolt
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      5. Attach the 2 claws to install the retractor cover of the rear seat belt assembly outer.

      6. Tighten the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      7. Tighten the bolt to connect the shoulder side of the rear seat belt assembly outer.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      8. Attach the 2 claws to close the shoulder side cover of the rear seat belt assembly outer.

      9. Tighten the bolt to connect the floor side of the rear seat belt assembly outer.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      10. w/ Cover:

        Attach the 3 guides and 3 claws to install the side trim cover.

    7. Check if the ELR locks.

      Note

      This check should be performed with the rear seat belt assembly outer installed.


      1. With the rear seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the rear seat belt assembly outer.

  53. INSTALL REAR NO. 4 SEAT ASSEMBLY

    Install the rear No. 4 seat assembly Click here.

  54. INSTALL REAR NO. 3 SEAT ASSEMBLY


    1. for Bench Type Seatback:

      Install the rear No. 3 seat assembly Click here.

    2. for Separate Type Seatback:

      Install the rear No. 3 seat assembly Click here.

  55. INSTALL REAR NO. 2 SEAT ASSEMBLY


    1. w/ Headrest:

      Install the rear No. 2 seat assembly Click here.

    2. w/o Headrest:

      Install the rear No. 2 seat assembly (See page ( Click here).

  56. INSTALL REAR NO. 1 SEAT ASSEMBLY


    1. for Fixed Seat Type:

      Install the rear No. 1 seat assembly Click here.

    2. for Fold Down Seat Type:

      Install the rear No. 1 seat assembly Click here.

    3. for Swiveling Seat Type:

      Install the rear No. 1 seat assembly Click here.

    4. w/ Headrest:

      Install the rear No. 1 seat assembly Click here.

    5. w/o Headrest:

      Install the rear No. 1 seat assembly Click here

  57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.