SLIDE DOOR CLOSER SYSTEM Slide Door Closer Motor LH Circuit

DESCRIPTION



WIRING DIAGRAM


  1. w/ Power Slide Door

    A003GGQE01

  2. w/o Power Slide Door

    A003CCKE01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK VEHICLE TYPE


    1. Check vehicle type.

      Result
      Result Proceed to
      w/o Power Slide Door A
      w/ Power Slide Door B

    B

    INSPECT POWER SLIDE DOOR LOCK ASSEMBLY LH Click here

    A

  2. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY LH


    1. Check the motor.


      1. Remove the power slide door lock assembly LH Click here.

      2. Inspect the power slide door lock assembly LH Click here.

    2. Check the switches.


      1. Remove the power slide door lock assembly LH Click here.

      2. Inspect the power slide door lock assembly LH Click here.

      Result
      Result Proceed to
      OK A
      NG (malfunctioning in motor) B
      NG (malfunctioning in switches) C

    B

    REPLACE POWER SLIDE DOOR LOCK ASSEMBLY LH Click here

    C

    REPLACE DOOR LOCK SWITCH LH

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  3. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY LH


    1. Check the motor.


      1. Remove the power slide door lock assembly LH Click here.

      2. Inspect the power slide door lock assembly LH Click here.

    2. Check the switches.


      1. Remove the power slide door lock assembly LH Click here.

      2. Inspect the power slide door lock assembly LH Click here.

      Result
      Result Proceed to
      OK A
      NG (malfunctioning in motor) B
      NG (malfunctioning in switches) C

    B

    REPLACE POWER SLIDE DOOR LOCK ASSEMBLY LH Click here

    C

    REPLACE DOOR LOCK SWITCH LH

    A

  4. INSPECT NO. 2 REAR DOOR WIRE


    1. A003CQ3E01
      Text in Illustration
      *a

      No. 2 Rear Door Wire

      (Door Control Relay Assembly Side)
      *b

      No. 2 Rear Door Wire

      (Power Slide Door Lock Assembly LH Side)

      Disconnect the oq1 and po2 No. 2 rear door wire connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-4 - B-18 Always Below 1 Ω
      A-5 - B-12 Always Below 1 Ω
      A-7 - B-8 Always Below 1 Ω
      A-10 - B-16 Always Below 1 Ω
      A-11 - B-15 Always Below 1 Ω
      A-16 - B-14 Always Below 1 Ω
      A-17 - B-9 Always Below 1 Ω

    NG

    REPLACE NO. 2 REAR DOOR WIRE Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RELAY ASSEMBLY - POWER SLIDE DOOR LOCK ASSEMBLY LH)


    1. Disconnect the q3 and q4 door control relay assembly connectors.

    2. Disconnect the p1 power slide door lock assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      q3-1 (DC-) - p1-1 (ACT-) Always Below 1 Ω
      q3-5 (DC+) - p1-2 (ACT+) Always Below 1 Ω
      q4-4 (HAF) - p1-3 (L1) Always Below 1 Ω
      q4-5 (FUL) - p1-4 (LS1) Always Below 1 Ω
      q4-18 (POL) - p1-9 (LSSR) Always Below 1 Ω
      q4-19 (LMT) - p1-10 (UL) Always Below 1 Ω
      q4-13 (OSG) - p1-8 (E2) Always Below 1 Ω
      q3-1 (DC-) or p1-1 (ACT-) - Body ground Always 10 kΩ or higher
      q3-5 (DC+) or p1-2 (ACT+) - Body ground Always 10 kΩ or higher
      q4-4 (HAF) or p1-3 (L1) - Body ground Always 10 kΩ or higher
      q4-5 (FUL) or p1-4 (LS1) - Body ground Always 10 kΩ or higher
      q4-18 (POL) or p1-9 (LSSR) - Body ground Always 10 kΩ or higher
      q4-19 (LMT) or p1-10 (UL) - Body ground Always 10 kΩ or higher
      q4-13 (OSG) or p1-8 (E2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here