POWER SLIDE DOOR SYSTEM DTC CHECK / CLEAR


  1. VEHICLE INITIAL SETTING


    1. Stop the engine.

    2. Prepare the vehicle by making sure these slide operational conditions are met.


      1. Battery voltage is 11 V or more.

      2. The power slide door main switch is ON.

      3. The slide door lock is unlocked (the position switch is ON).

      4. The shift lever is in the P position.

    3. Fully close the slide door.


    NEXT

  2. SELF-DIAGNOSTIC MODE 1


    1. A003BY0E01

      Enter self-diagnostic mode 1.


      1. Turn OFF the power slide door main switch.

      2. Turn the ignition switch ON.

      3. Within 10 seconds, push the auto slide door control switch 10 times.

      4. Check that the buzzer sounds (see buzzer pattern 1).

      5. Within 3 seconds, turn ON the power slide door main switch.

      6. Check that the buzzer sounds (see buzzer pattern 2) and that the system enters self-diagnostic mode 1.

    2. Start the inspection.

      Note

      If the slide door operational conditions are not followed exactly, the system will change from self-diagnostic mode to normal operation mode.


      1. Push the auto slide door control switch assembly and fully open the slide door.

      2. Pull the inside door handle, and fully close the slide door.

        Note

        If the outside door handle is operated during this inspection, a self-diagnostic code may be output when the system enters self-diagnostic mode 2, regardless of the status (normal/malfunctioning) of the slide door.

      3. Perform the operations described in the table below.

      4. When changes in the input signals are detected, check that the buzzer emits a sound for 0.5 seconds. If the buzzer does not sound, proceed to the relevant troubleshooting page in accordance with the table.

        Target Items Inspection Operations Proceed to
        Shift lever (Park/neutral position switch)

        P position ←→ Expect P

        (Release shift lock before inspection)

        		 A
        Vehicle speed Less than 3 km/h (1 mph) ←→ 3 km/h (1 mph) or more B
        Slide door lock remote control assembly LH (door lock switch) ON ←→ OFF C
        Slide door lock remote control assembly RH (door lock switch) (for RH Side, w/ Power Slide Door) ON ←→ OFF D

        • Power slide door sensor assembly

        • Power slide door sensor assembly RH (for RH Side, w/ Power Slide Door)

        		 ON ←→ OFF E

    Tech Tips

    When necessary to return to the normal operation mode, go to step 5.


    A

    Go to flowchart Click here

    B

    Go to flowchart Click here

    C

    Go to flowchart Click here

    D

    Go to flow chart Click here

    E

    Go to flowchart Click here

    NEXT

  3. SELF-DIAGNOSTIC MODE 2


    1. A003E00E02

      Change from self-diagnostic mode 1 to self-diagnostic mode 2.


      1. After the system has changed to self-diagnostic mode 1, press the auto slide door control switch assembly for less than 0.5 seconds.

      2. If the buzzer sounds twice, the system has successfully entered self-diagnostic mode 2.

    2. Start the inspection.


      1. Check that codes that have been detected during self-diagnostic mode 1 are output using these buzzer patterns.

        A003FB6E01
        Next step Proceed to
        Normal operation mode A
        Self-diagnostic mode 3 B

        Note

        If the system returns to normal operation mode from self-diagnostic mode, the codes saved in its memory will be erased. When necessary, change to self-diagnostic mode 3 and perform confirmation before returning to normal operation mode.


    A

    Go to step 6
    B

  4. SELF-DIAGNOSTIC MODE 3


    1. A003E00E01

      Change from self-diagnostic mode 2 to self-diagnostic mode 3.


      1. After the system has changed to self-diagnostic mode 2, press the auto slide door control switch assembly for less than 0.5 seconds.

      2. If the buzzer sounds twice, the system has successfully entered self-diagnostic mode 3.

    2. Start the inspection.


      1. Check the codes that were recorded in memory when a malfunction was detected in past operations through buzzer patterns.

        Tech Tips

        Codes are output in the same way as in self-diagnostic mode 2.

    3. Change from self-diagnostic mode 3 to normal operation mode.

      Note

      If the system returns to normal operation mode from self-diagnostic mode, all the codes saved in its memory will be erased.

      Tech Tips

      When one of the following conditions is met, the buzzer sounds twice and changes to normal operation mode.


      1. The ignition switch is turned OFF.

      2. The power slide door main switch is turned OFF.

      3. The auto slide door control switch assembly is pushed for less than 0.5 seconds.


    END

    TO NORMAL OPERATION MODE

  5. CHANGE FROM SELF-DIAGNOSTIC MODE 1 TO NORMAL OPERATION MODE


    1. The system changes from self-diagnostic mode 1 to normal operation mode when either of the following conditions is met:


      1. The ignition switch is turned OFF.

      2. The power slide door main switch is turned OFF.


    END

    TO NORMAL OPERATION MODE

  6. CHANGE FROM SELF-DIAGNOSTIC MODE 2 TO NORMAL OPERATION MODE


    1. The system changes from self-diagnostic mode 2 to normal operation mode when either of the following conditions is met:

      Note

      If the system returns to normal operation mode from self-diagnostic mode, all the codes saved in its memory will be erased.


      1. The ignition switch is turned OFF.

      2. The power slide door main switch is turned OFF.


    END
    TO NORMAL OPERATION MODE