ECD SYSTEM (w/ DPF), Diagnostic DTC:P245C, P245D

DTC Code DTC Name
P245C Exhaust Gas Recirculation Cooler Bypass Control Circuit Low
P245D Exhaust Gas Recirculation Cooler Bypass Control Circuit High

DESCRIPTION

The vacuum switching valve (for EGR bypass valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

P245C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
  • Open or short in vacuum switching valve (for EGR bypass valve) circuit

  • Vacuum switching valve (for EGR bypass valve)

  • ECM

P245D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
  • Open or short in vacuum switching valve (for EGR bypass valve) circuit

  • Vacuum switching valve (for EGR bypass valve)

  • ECM

WIRING DIAGRAM

A003ARIE09

INSPECTION PROCEDURE

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • After replacing the fuel supply pump assembly, the ECM needs initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)


    1. Inspect the vacuum switching valve (for EGR bypass valve) Click here.


    NG
    OK
  2. CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)


    1. A003F0FE38
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Vacuum Switching Valve (for EGR Bypass Valve))

      Disconnect the vacuum switching valve (for EGR bypass valve) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      D74-1 - Body ground Ignition switch ON 11 to 14 V
    3. Reconnect the vacuum switching valve (for EGR bypass valve) connector.


    NG
    OK
  3. CHECK HARNESS AND CONNECTOR ((VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM))


    1. Disconnect the vacuum switching valve (for EGR bypass valve) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D74-2 - D99-106 (ECBV) Always Below 1 Ω
      D74-2 or D99-106 (ECBV) - Body ground Always 10 kΩ or higher
    4. Reconnect the vacuum switching valve (for EGR bypass valve) connector.

    5. Reconnect the ECM connector.


    NG
    OK
  4. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT
  5. REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)


    1. Replace the vacuum switching valve (for EGR bypass valve) Click here.


    NEXT
  6. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Tech Tips

      If the voltage at the vacuum switching valve (for EGR bypass valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve (for EGR bypass valve) and EFI MAIN relay.


    NEXT
  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch to ON for 3 seconds.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Confirm that the DTC is not output again.


    NEXT