OIL AND OIL FILTER REPLACEMENT

CAUTION:


  • Prolonged and repeated contact with engine oil will cause the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants that may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.


  1. REMOVE NO. 2 ENGINE SERVICE HOLE COVER (for Standard Body)


    1. Detach the clips and fold back the carpet.

    2. A003F0N

      Remove the 3 bolts and No. 2 engine service hole cover.

  2. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Wipe the oil pan and oil pan drain plug.

    4. Install a new gasket and the oil pan drain plug.

      Torque:
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }

  3. REMOVE OIL FILTER SUB-ASSEMBLY


    1. A003DXRE02

      Using SST, remove the oil filter.

      SST
      09228-07501

      Tech Tips


      • Position the drain oil container to collect the oil from the oil filter.

      • Insert cloth, etc. between the oil filter and oil cooler cover to prevent engine oil from dripping out.

      • When engine oil starts coming out of the oil filter, briefly stop loosening the oil filter to prevent engine oil from flowing out from the oil cooler cover.

  4. INSTALL OIL FILTER SUB-ASSEMBLY


    1. Check and clean the oil filter installation surface.

    2. Apply clean engine oil to the gasket of a new oil filter.

    3. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

    4. A003GTQE02

      Using SST, tighten the oil filter 3/4 of a turn by hand or with a common wrench.

      SST
      09228-07501
      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  5. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Item Oil Grade Oil Viscosity (SAE)
      w/ DPF

      ACEA C2

      (Using engine oil other than ACEA C2 may damage catalytic converter)

      - 0W-30

      - 5W-30
      w/o DPF

      G-DLD1, API CF-4, CF or ACEA B1

      (You may also use API CE or CD)

      - 5W-30

      - 10W-30

      - 15W-40

      - 20W-50
      Standard Capacity (w/ DPF)
      Item Fill Amount
      Drain and refill without oil filter change 6.6 liters (7.0 US qts, 5.8 Imp. qts)
      Drain and refill with oil filter change 6.8 liters (7.2 US qts, 6.0 Imp. qts)
      Dry fill 7.5 liters (7.9 US qts, 6.6 Imp. qts)
      Standard Capacity (w/o DPF)
      Item Fill Amount
      Drain and refill without oil filter change 6.8 liters (7.2 US qts, 6.0 Imp. qts)
      Drain and refill with oil filter change 7.0 liters (7.4 US qts, 6.2 Imp. qts)
      Dry fill 7.7 liters (8.1 US qts, 6.8 Imp. qts)

    2. Install the oil filler cap.

  6. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  7. INSTALL NO. 2 ENGINE SERVICE HOLE COVER (for Standard Body)


    1. Install the No. 2 engine service hole cover with the 3 bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

    2. Return the carpet to its original position and attach the clips.

  8. INSPECT ENGINE OIL LEVEL