HOOD LOCK CONTROL CABLE ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE RADIATOR SUPPORT OPENING COVER

    Click here

  4. REMOVE FRONT FENDER LINER LH

    Click here

  5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  6. REMOVE HOOD LOCK ASSEMBLY


    1. A004UB5E02
      *1 w/o Engine Hood Courtesy Switch:
      *2 w/ Engine Hood Courtesy Switch:

      Remove the 3 bolts and hood lock.

    2. Disconnect the hood lock control cable.

    3. w/ Engine Hood Courtesy Switch:

      Disconnect the connector.

  7. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A004TMM

      Detach the 3 claws.

    2. Disconnect the hood lock control cable and remove the hood lock lever.

  8. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. A004OIHE02
      Text in Illustration
      *1 Hood Lock Control Cable
      *2 String
      *3 Dash to Frame Brace
      *4 Engine Room Main Wire
      *5 Instrument Panel Wire
      *6 Hood Lock Control Cable Grommet
      *7 Floor Wire

      Tie a string to the end of the hood lock control cable assembly as shown in the illustration.

      Note

      Use a length of string long enough to pass through the engine compartment.

    2. Using a screwdriver, disconnect the clamps shown in the illustration.

      A004N02E02
      Text in Illustration
      *1 Hood Lock Control Cable *6 Apron
      *2 Clamp *7

      w/ Rear Wiper:

      Rear Washer Hose
      *3 Bypass Hose *8 Grommet
      *4 Radiator Support Side *9 Hood Lock Control Cable Grommet
      *5 Fender Liner *10 Plug Hole

      Tech Tips

      Tape the screwdriver tip before use.

    3. Pull the cable from the engine room and remove it.

  9. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. A004P6SE02
      Text in Illustration
      *1 Hood Lock Control Cable
      *2 String
      *3 Dash to Frame Brace
      *4 Engine Room Main Wire
      *5 Instrument Panel Wire
      *6 Hood Lock Control Cable Grommet

      Tie a string to the end of the hood lock control cable assembly as shown in the illustration.

      Note

      Use a length of string long enough to pass through the engine compartment.

    2. Using a screwdriver, disconnect the clamps shown in the illustration.

      A004SZLE02
      Text in Illustration
      *1 Hood Lock Control Cable *7 Fender Liner
      *2 Clamp *8 Apron
      *3 Clamp *9

      w/ Rear Wiper:

      Rear Washer Hose
      *4 Bypass Hose *10 Grommet
      *5 Radiator Support *11 Hood Lock Control Cable Grommet
      *6 Radiator Support Side *12 Plug Hole

      Tech Tips

      Tape the screwdriver tip before use.

    3. Pull the cable from the engine room and remove it.