POWER WINDOW CONTROL SYSTEM Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION


WIRING DIAGRAM

A004PV3E04

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK LIN COMMUNICATION SYSTEM


    1. Check for LIN communication system DTCs related to the power window control system Click here.

      OK
      LIN communication system DTCs are not output.

    NG

    GO TO LIN COMMUNICATION SYSTEM Click here

    OK

  2. CHECK FOR DTC (B2312)


    1. Check if DTC B2312 is output Click here.

      OK
      DTC B2312 is not output.

    NG

    GO TO DTC B2312 Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)


    1. Use the Data List to check if the power window regulator master switch is functioning properly Click here.

      D-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Up SW Driver side power window manual up signal / ON or OFF

      ON: Driver side power window manual up switch operated

      OFF: Driver side power window switch not operated

      		 -
      D Door P/W Down SW Driver side power window manual down signal / ON or OFF

      ON: Driver side power window manual down switch operated

      OFF: Driver side power window switch not operated

      		 -
      OK
      The display changes according to operation of the power window regulator master switch.
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH Click here

    B

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH Click here

    C

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

    A004SG3E06
    Text in Illustration
    *1 for LHD
    *2 for RHD
    *3

    Front view of wire harness connector

    (to Power Window Regulator Master Switch)

    1. Disconnect the E14*1 or E8*2 switch connector.

      *1: for LHD

      *2: for RHD

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      E14-11 (B) - Body ground Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      E8-11 (B) - Body ground Always 11 to 14 V
      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E14-12 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      E8-12 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (FRONT DOOR WINDOW REGULATOR ASSEMBLY - BATTERY AND BODY GROUND)

    A004O2AE10
    Text in Illustration
    *1 for LHD
    *2 for RHD
    *3

    Front view of wire harness connector

    (to Front Door Window Regulator)

    1. Disconnect the E15*1 or E6*2 regulator connector.

      *1: for LHD

      *2: for RHD

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      E15-2 (B) - Body ground Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      E6-2 (B) - Body ground Always 11 to 14 V
      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E15-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      E6-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY)

    A004PWGE10
    Text in Illustration
    *1 for LHD
    *2 for RHD
    *3

    Front view of wire harness connector

    (to Power Window Regulator Master Switch)
    *4

    Front view of wire harness connector

    (to Front Door Window Regulator)

    *1: for LHD

    *2: for RHD


    1. Disconnect the E14*1 or E8*2 switch connector.

    2. Disconnect the E15*1 or E6*2 regulator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E14-20 (UP) - E15-10 (UP) Always Below 1 Ω
      E14-15 (DOWN) - E15-7 (DOWN) Always Below 1 Ω
      E14-20 (UP) or E15-10 (UP) - Body ground Always 10 kΩ or higher
      E14-15 (DOWN) or E15-7 (DOWN) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      E8-20 (UP) - E6-10 (UP) Always Below 1 Ω
      E8-15 (DOWN) - E6-7 (DOWN) Always Below 1 Ω
      E8-20 (UP) or E6-10 (UP) - Body ground Always 10 kΩ or higher
      E8-15 (DOWN) or E6-7 (DOWN) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    B

    INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY RH Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  7. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

    A004NUME03
    *1 UP
    *2 DOWN

    1. Remove the door window regulator Click here.

    2. Check that the window regulator moves smoothly as follows.

      Note


      • Do not apply positive (+) battery voltage to any terminal other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.


      • Reset the door window regulator (initialize the pulse sensor) after installing the door window regulator onto the door.

      OK
      Measurement Condition Specified Condition

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.

      		 Arm of window regulator rotates counterclockwise (Up)

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.

      		 Arm of window regulator rotates clockwise (Down)

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    NG

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH Click here

  8. INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY RH

    A004PBYE03
    *1 UP
    *2 DOWN

    1. Remove the door window regulator Click here.

    2. Check that the window regulator moves smoothly as follows.

      Note


      • Do not apply positive (+) battery voltage to any terminal other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.


      • Reset the door window regulator (initialize the pulse sensor) after installing the door window regulator onto the door.

      OK
      Measurement Condition Specified Condition

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.

      		 Arm of window regulator rotates clockwise (Up)

      1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

      2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

      3. Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.

      		 Arm of window regulator rotates counterclockwise (Down)

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    NG

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH Click here