ROOF HEADLINING(for Wagon) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL TONNEAU COVER HOLDER BRACKET LH (w/ Partition Net)

    A004O2R

    1. Install the tonneau cover holder bracket with the 2 bolts.

  2. INSTALL TONNEAU COVER HOLDER BRACKET RH (w/ Partition Net)

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL NO. 2 DECK BOARD BRACKET

    A004RYW

    1. Install the No. 2 deck board bracket with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  4. INSTALL NO. 1 DECK BOARD BRACKET

    Tech Tips

    Use the same procedure described for the No. 2 deck board bracket.

  5. INSTALL NO. 4 LUGGAGE COMPARTMENT TRIM BRACKET (w/o Deck Rail)

    A004PWS

    1. Install the No. 4 luggage compartment trim bracket with the bolt.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }

  6. INSTALL NO. 3 LUGGAGE COMPARTMENT TRIM BRACKET (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 4 luggage compartment trim bracket.

  7. INSTALL FRONT DECK RAIL BRACKET LH (w/ Deck Rail)

    A004MOSE03

    1. Install the front deck rail bracket with the 2 bolts.

      Torque:
      for bolt A
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }
      for bolt B
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  8. INSTALL FRONT DECK RAIL BRACKET RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL REAR NO. 3 SIDE RAIL SPACER LH

    A004SIV

    1. Attach the 2 claws to install the No. 3 side rail spacer.

  10. INSTALL REAR NO. 3 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL REAR NO. 2 SIDE RAIL SPACER LH

    Click here

  12. INSTALL REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    Click here

  14. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

    Click here

  16. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

    Click here

  18. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. INSTALL ROOF HEADLINING ASSEMBLY

    A004PSM

    Tech Tips

    Before installing the roof headlining, move the front seats and rear seat to the positions shown in the illustration.


    1. A004U76

      Place the roof headlining into the vehicle through the back door.

      Note

      Be careful not to damage the roof headlining when placing it in the cabin.

    2. w/o Roof Sunshade System:


      1. Install the roof headlining with the 5 clips.

        A004UCF

    3. w/ Roof Sunshade System:


      1. Attach the 3 guides and 12 fasteners to install the roof headlining.

      2. Install the 5 clips.

        A004SMXE02
        Text in Illustration
        *1 Guide *2 Fastener

    4. for LHD:


      1. A004SYVE03
        *1 for LHD:

        Connect the 2 roof wire connectors.

      2. A004Q6VE03
        *1 for LHD:

        Connect the 2 clamps.

    5. for RHD:


      1. A004TUVE03
        *1 for RHD:

        Connect the roof wire connector.

      2. A004TMVE03
        *1 for RHD:

        Connect the 2 clamps and connector.

    6. A004OK2

      Connect the 4 clamps to the front pillar LH.

    7. A004O9U

      w/ Roof Sunshade System:

      Connect the connector.

    8. A004S8K

      Install the antenna with the 2 bolts.

    9. Connect the 3 clamps to the rear pillar RH.

    10. Connect the 3 connectors.

    11. A004QQ4

      Connect the 3 clamps to the front pillar RH.

    12. Connect the connector.

    13. A004SP6

      w/ Lane Keeping Assist System:

      Tech Tips


      • Use the same procedure for RHD and LHD vehicles.

      • The procedure listed below is for LHD vehicles.


      1. Connect the connector and attach the clamp.

    14. A004SXD

      w/ Rain Sensor:

      Connect the rain sensor connector.

    15. A004PRD

      w/ EC Mirror:

      Connect the EC mirror connector.

  20. INSTALL REAR ROOM PARTITION NET HOOK LH

    A004NCY

    1. Attach the 2 claws to install the rear room partition net hook.

    2. Install the screw.

  21. INSTALL REAR ROOM PARTITION NET HOOK RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. INSTALL ASSIST GRIP SUB-ASSEMBLY

    Click here

  23. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    Click here

  24. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. INSTALL VISOR HOLDER

    Click here

  26. INSTALL VISOR ASSEMBLY LH

    Click here

  27. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  29. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. w/o Rear Monitor:

      Install the inner rear view mirror stay holder cover Click here.

    2. w/ Rear Monitor:

      Install the inner rear view mirror stay holder cover Click here.

  30. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  31. INSTALL FRONT ROOF TOP GARNISH (w/ Lane Keeping Assist System)

    Click here

  32. INSTALL MAP LIGHT ASSEMBLY

    Click here

  33. INSTALL COIN BOX ASSEMBLY

    Click here

  34. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips


    • Use the same procedure for RHD and LHD vehicles.

    • The procedure listed below is for LHD vehicles.


    1. Install the upper instrument panel sub-assembly Click here.

  35. INSTALL INNER ROOF SIDE GARNISH LH

    A004T80E03
    Text in Illustration
    *1 Clip A

    1. Install a new clip A to the inner roof side garnish.

    2. Attach the 7 clips to install the inner roof side garnish.

  36. INSTALL INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Pass the fuel lid opener cable through the deck trim side panel.

    2. Connect the connector.

    3. Attach the 7 clips and 3 claws to install the deck trim side panel.

    4. Install the bolt and clip.

      A004RPEE02
      Text in Illustration
      *1 Fuel Lid Opener Cable - -

  38. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Attach the 7 clips and 3 claws to install the deck trim side panel.

    2. Install the bolt and clip.

      A004T57

  39. INSTALL INNER ROOF SIDE GARNISH CAP LH

    A004MWE

    1. Attach the 2 claws to install the inner roof side garnish cap.

  40. INSTALL INNER ROOF SIDE GARNISH CAP RH

    Tech Tips

    Use the same procedure described for the LH side.

  41. INSTALL CENTER PILLAR GARNISH LH

    Click here

  42. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  43. INSTALL LAP BELT OUTER ANCHOR COVER

    Click here

  44. INSTALL LOWER CENTER PILLAR GARNISH LH

    Click here

  45. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  46. INSTALL FRONT PILLAR GARNISH LH


    1. Remove the protective cover.

    2. Install a new front pillar garnish clip to the front pillar garnish.

      Tech Tips

      Install the front pillar garnish clip so that it faces as shown in the illustration.

      A004OEKE01
      Text in Illustration
      *a CORRECT *b INCORRECT
    3. A004PK8

      Attach the 2 guides.

    4. A004MNFE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Attach the 2 clips to install the front pillar garnish.

  47. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  48. INSTALL BACK DOOR WEATHERSTRIP

    A004POA

    1. Align the center mark of the back door weatherstrip with the position indicated by the arrow in the illustration and install a new back door weatherstrip.

  49. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A004QU6E01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Install the rear door opening trim weatherstrip as shown in the illustration.

  50. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. INSTALL REAR DOOR SCUFF PLATE LH

    Click here

  52. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  53. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  54. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  55. INSTALL COWL SIDE TRIM BOARD LH

    Click here

  56. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  57. INSTALL FRONT DOOR SCUFF PLATE LH

    Click here

  58. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  59. INSTALL FRONT DECK FLOOR BOX

    A004OEG

    1. Attach the 4 guides to install the front deck floor box.

    2. Install the 2 clips.

  60. INSTALL REAR FLOOR FINISH PLATE

    A004NWX

    1. Attach the 4 clips to install the rear floor finish plate.

  61. INSTALL DECK FLOOR BOX LH

    A004QR4

    1. Attach the 5 guides to install the deck floor box.

  62. INSTALL DECK FLOOR BOX RH

    Tech Tips

    Use the same procedure described for the LH side.

  63. INSTALL ROPE HOOK ASSEMBLY (w/o Deck Rail)

    A004PBP

    Tech Tips

    Use the same procedure for all the rope hooks.


    1. Install the rope hook with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  64. INSTALL NO. 6 DECK SIDE TRIM COVER (w/o Deck Rail)

    A004Q1X

    1. Attach the 3 claws to install the No. 6 deck side trim cover.

  65. INSTALL NO. 5 DECK SIDE TRIM COVER (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 6 deck side trim cover.

  66. INSTALL NO. 2 DECK SIDE TRIM COVER (w/o Deck Rail)

    A004PMU

    1. Attach the 2 clips and 3 guides to install the No. 2 deck side trim cover.

  67. INSTALL NO. 1 DECK SIDE TRIM COVER (w/o Deck Rail)

    Tech Tips

    Use the same procedure described for the No. 2 deck side trim cover.

  68. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)

    A004QS7

    1. Install the floor side rail with the 3 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  69. INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  70. INSTALL REAR DECK FLOOR BOX


    1. Attach the 7 guides to install the rear deck floor box.

      A004TODE01
      *1 w/ Spare Tire:
      *2 w/o Spare Tire:
    2. A004QH1

      Install the bolt.

    3. A004RFL

      Install the bolt.

  71. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. Attach the clip to install the No. 3 deck board.

      A004TWVE01
      *1 w/o Deck Rail:
      *2 w/ Deck Rail:

  72. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the No. 3 deck board.

  73. INSTALL DECK BOARD SUB-ASSEMBLY

    A004QDV

    1. Pull the lever to install the deck board.

  74. INSTALL DECK BOARD ASSEMBLY

    A004U1M

    1. Attach the clip and 2 guides to install the deck board.

  75. INSTALL LOWER DECK TRIM SIDE BOARD LH (w/ Partition Board)


    1. Install the lower deck trim side board.

  76. INSTALL LOWER DECK TRIM SIDE BOARD RH (w/ Partition Board)


    1. Install the lower deck trim side board.

  77. INSTALL ROOM PARTITION NET ASSEMBLY (w/ Partition Net)

    A004PW9

    1. Install the room partition net.

  78. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A004TFC

    1. Pull the lever to install the tonneau cover.

  79. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    Click here

  80. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  81. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    Click here

  82. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.