LOWER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND BOLT

    Tech Tips

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

    A004SOZE01

  2. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the Autoaway/Return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.

    2. Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column.

    3. Turn the ignition switch off.

  3. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Remove the upper instrument panel sub-assembly Click here.

  6. REMOVE STEERING WHEEL ASSEMBLY


    1. Remove the steering wheel assembly Click here.

  7. REMOVE LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  8. REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  9. REMOVE LOWER NO. 2 STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  10. REMOVE LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  11. REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  12. REMOVE TILT AND TELESCOPIC SWITCH (for Power Tilt and Power Telescopic Steering Column)

    Click here

  13. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Click here

  14. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Audio)


    1. A004U09

      Remove the 4 screws and cover with bracket.

  15. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Audio)


    1. for Radio Receiver Type:

      Remove the radio receiver assembly Click here.

    2. for Radio and Display Type:

      Remove the radio receiver assembly Click here.

  16. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

    Click here

  17. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)

    Click here

  18. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle)

    Click here

  19. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (for Automatic Transaxle)

    Click here

  20. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL

    Click here

  21. REMOVE REAR CONSOLE BOX CUP HOLDER

    Click here

  22. REMOVE CONSOLE BOX CARPET

    Click here

  23. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  24. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  25. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)


    1. A004PWZ

      Using a moulding remover B, detach the 2 claws and 4 clips.

    2. Disconnect the connectors and remove the switch hole base.

  26. REMOVE NO. 1 SWITCH HOLE BASE (for RHD)


    1. Using a moulding remover B, detach the 3 claws and 4 clips.

    2. Disconnect the connectors and remove the switch hole base.

      A004ODKE01
      *1 w/o Entry and Start System:
      *2 w/ Entry and Start System:

  27. REMOVE COIN BOX ASSEMBLY


    1. A004P9A

      Slightly bend the upper part of the coin box to release the 2 stoppers and open the coin box until it is horizontal.

    2. A004TA0

      Pull the coin box toward the rear of the vehicle to detach the 2 hinges and remove the coin box.

  28. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A004U23

      Remove the 2 screws <A>.

    2. Detach the claw.

    3. A004S1P

      Disconnect each connector.

    4. Detach the guide and remove the under cover.

  29. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  30. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A004TKP

      Detach the 3 claws.

    2. A004MPU

      Disconnect the connector.

    3. Detach the guide and remove the under cover.

  31. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  32. REMOVE FRONT DOOR SCUFF PLATE RH

    Click here

  33. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  34. REMOVE COWL SIDE TRIM BOARD RH

    Click here

  35. REMOVE GLOVE BOX LIGHT ASSEMBLY

    Click here

  36. REMOVE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

    Click here

  37. REMOVE ENGINE SWITCH (for LHD with Entry and Start System)


    1. A004MW9

      Detach the 2 claws.

    2. Disconnect the connector and remove the switch.

  38. REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)

    Click here

  39. REMOVE HEADLIGHT SWIVEL MAIN SWITCH (w/ AFS)

    Click here

  40. REMOVE VSC OFF SWITCH

    Click here

  41. REMOVE FUEL LID OPENER SWITCH

    Click here

  42. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  43. REMOVE COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR (for Automatic Air Conditioning System)


    1. A004NUT

      Disconnect the connector and then detach the 2 claws.

    2. Disconnect the hose and remove the thermistor.

  44. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Remove the 2 bolts <B> and 8 screws <C>.

    2. Remove the screw <D>.

    3. Remove the screw.

      A004QWCE01
      Text in Illustration
      *1 Bolt <B> *3 Screw <D>
      *2 Screw <C> - -

    4. Remove the 2 bolts.

    5. Detach the 10 clamps.

    6. Detach the claw and remove the instrument panel.

      A004PM6