UPPER INSTRUMENT PANEL INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL GLOVE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY

    A004T4N

    1. Insert the bottom side of the glove compartment door lock cylinder as shown in the illustration, hold down the stopper and install the glove compartment door lock cylinder.

  2. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Securely attach the 6 claws and 4 clips of the instrument panel to the vehicle body.

    2. Install the instrument panel with the 3 screws <C>.

      A004N2X

    3. Install the passenger airbag bolt <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    4. Connect the connectors and clamp.

      A004OH2E01
      *1 for 11 Speakers:
    5. A004PDX

      When replacing the upper instrument panel sub-assembly with a new one:


      1. Twist the rib (the piece used to maintain the shape of the panel) in the direction of the arrow in the illustration until it detaches from the instrument panel, and remove the rib.

  3. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 11 Speakers)


    1. A004S3C

      Attach the 2 clips and 3 claws to install the speaker panel.

  4. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  5. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 11 Speakers)

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel speaker panel.

  6. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel speaker panel.

  7. INSTALL FRONT PILLAR GARNISH LH (for Sedan)

    Click here

  8. INSTALL FRONT PILLAR GARNISH LH (for Wagon)

    Click here

  9. INSTALL FRONT PILLAR GARNISH RH (for Sedan)

    Click here

  10. INSTALL FRONT PILLAR GARNISH RH (for Wagon)

    Click here

  11. INSTALL INSTRUMENT SIDE PANEL LH


    1. A004TNV

      Attach the 2 hooks.

    2. A004PFZ

      Attach the 3 clips and 4 claws to install the side panel.

  12. INSTALL INSTRUMENT SIDE PANEL RH


    1. A004TY0E01
      Text in Illustration
      *1 w/ Airbag Cut Off Switch Cylinder

      Attach the 2 hooks.

    2. w/ Airbag Cut Off Switch Cylinder:


      1. Connect the connector.

    3. A004TRC

      Attach the 3 clips and 4 claws to install the side panel.

  13. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL (w/ Audio)


    1. A004Q5I

      Connect the connector and clamp.

    2. A004O2K

      Attach the 2 clips and hook.

    3. A004OMD

      Attach the 2 clips.

    4. Attach the 3 claws and 3 hooks to install the panel register.

  14. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL (w/o Audio)


    1. A004Q5I

      Connect the connector and clamp.

    2. A004S2N

      Attach the 2 clips and hook.

    3. A004SYK

      Attach the 6 clips.

    4. Attach the 3 claws and 3 hooks to install the panel register.

  15. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Attach the 4 clips and 5 claws to install the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Connect the connector.

      2. Attach the 4 clips and 5 claws to install the panel end.

        A004SZGE01
        *1 w/o TOYOTA Parking Assist-sensor System:
        *2 w/ TOYOTA Parking Assist-sensor System:

  16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A004QPQ

      Attach the 2 hinges to install the door.

    2. A004O3UE01
      Text in Illustration
      *1 Stopper

      While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage the 2 stoppers.

  17. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A004U1R

      Attach the 4 clips and 5 claws to install the panel end.

  18. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. Attach the 4 clips and 5 claws to install the panel end.

      A004N4JE01
      *1 for LHD without Entry and Start System:
      *2 for LHD with Entry and Start System:

  19. INSTALL NO. 3 BOX PANEL

    Click here

  20. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A004TCFE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.

  21. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A004RMHE01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Attach the guide near the front of the vehicle.

    2. Attach the clamp.

    3. Attach the 2 clips and 5 claws to install the finish panel.

  22. INSTALL COMBINATION METER ASSEMBLY


    1. Install the combination meter assembly Click here.

  23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  24. RESTORE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)


    1. Restore the Autoaway/Return function setting to the previous condition by changing the customize parameter Click here.

  25. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.