REAR SEAT OUTER BELT ASSEMBLY(for Sedan) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. A004TEB

      Attach the guide and the outer belt anchor bracket sub-assembly LH.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. A004NBUE02
      Text in Illustration
      *1 Locking Button

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    2. for LH Side:


      1. A004U8BE01
        Text in Illustration
        *a Bolt
        *b Nut

        Attach the guide (A) and temporarily install the rear seat 3 point type belt assembly LH with the bolt and nut.

      2. Tighten the bolt and nut in the order shown in the illustration.

        Torque:
        for Bolt
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
        Torque:
        for Nut
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      3. Attach the wire harness clamp (B).

    3. for RH Side:


      1. A004NCOE01
        Text in Illustration
        *a Bolt
        *b Nut

        Attach the guide and temporarily install the rear seat 3 point type belt assembly LH with the bolt and nut.

      2. Tighten the bolt and nut in the order shown in the illustration.

        Torque:
        for Bolt
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
        Torque:
        for Nut
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL NO. 2 PACKAGE TRAY TRIM PAD

    Tech Tips

    Perform the following procedure if replacing the No. 2 package tray trim pad.


    1. A004TUEE05
      Text in Illustration
      *1 Mark

      Install a new No. 2 package tray trim pad using double-sided tape as shown in the illustration.

  4. INSTALL NO. 1 PACKAGE TRAY TRIM PAD

    Tech Tips

    Perform the following procedure if replacing the No. 1 package tray trim pad.


    1. A004NUDE03
      Text in Illustration
      *1 Mark

      Install 2 new No. 1 package tray trim pads using double-sided tape as shown in the illustration.

  5. INSTALL NO. 1 ROOM PARTITION BOARD

    A004R6L

    1. Attach the 4 clips to install the partition board.

    2. Install the 4 clips.

  6. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

    A004RUU

    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. Attach the 5 claws and 2 clips to install the package tray trim panel assembly.

    3. Install the 4 clips.

    4. Connect the connector.

  7. INSTALL REAR SEAT SHOULDER BELT HOLE COVER

    A004RV6

    1. Attach the 4 claws to install the belt hole cover.

      Tech Tips

      Use the same procedure to install all the belt hole covers.

  8. INSTALL INNER ROOF SIDE GARNISH LH

    Click here

  9. INSTALL INNER ROOF SIDE GARNISH RH

    Click here

  10. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

    Click here

  11. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    A004RMW

    1. Install the claw as shown in the illustration.

      Torque:
      7.8 N*m  { 80 kgf*cm, 69 in.*lbf }
    2. A004RC9E02
      Text in Illustration
      *1 Protruding Part

      Install the side seatback with the bolt.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt to overlap the protruding parts of the floor panel.

    3. Install the seat belt to the belt guide.

    4. Attach the claw to close the cap of the rear seat shoulder belt guide.

    5. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  12. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    Click here