REAR SEAT OUTER BELT ASSEMBLY(for Sedan) REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR BENCH TYPE SEAT CUSHION ASSEMBLY

    Click here

  4. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    A004P9F

    1. Remove the bolt and disconnect the outer belt anchor.

    2. A004Q46

      Using a screwdriver, detach the claw to open the cap of the rear seat shoulder belt guide.

    3. Remove the seat belt from the belt guide.

    4. A004QF9

      Remove the bolt and side seatback LH.

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

    Click here

  7. REMOVE INNER ROOF SIDE GARNISH LH

    Click here

  8. REMOVE INNER ROOF SIDE GARNISH RH

    Click here

  9. REMOVE REAR SEAT SHOULDER BELT HOLE COVER

    A004RT2

    1. Using a moulding remover, detach the 4 claws and remove the belt hole cover.

      Tech Tips

      Use the same procedure to remove all the belt hole covers.

  10. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

    A004RUU

    1. Disconnect the connector.

    2. Remove the 4 clips.

    3. Detach the 2 clips and raise the front portion of the package tray trim panel assembly.

    4. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    5. Detach the 5 claws and remove the package tray trim panel assembly.

  11. REMOVE NO. 1 ROOM PARTITION BOARD

    A004R6L

    1. Remove the 4 clips.

    2. Using a moulding remover, detach the 4 clips and remove the partition board.

  12. REMOVE NO. 1 PACKAGE TRAY TRIM PAD

    Tech Tips

    Perform the following procedure if replacing the No. 1 package tray trim pad.


    1. Remove the package tray trim pad.

  13. REMOVE NO. 2 PACKAGE TRAY TRIM PAD

    Tech Tips

    Perform the following procedure if replacing the No. 2 package tray trim pad.


    1. Remove the package tray trim pad.

  14. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. for LH Side:


      1. A004QOQE01
        Text in Illustration
        *a Bolt
        *b Nut

        Using a clip remover, detach the wire harness clamp (A).

      2. Remove the bolt and nut.

      3. Detach the guide and remove the rear seat 3 point type belt assembly LH.

    2. for RH Side:


      1. A004PCQE01
        Text in Illustration
        *a Bolt
        *b Nut

        Remove the bolt and nut.

      2. Detach the guide and remove the rear seat 3 point type belt assembly RH.

    3. A004NK9E02
      Text in Illustration
      *1 Locking Button
      *a Protective Tape

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  15. REMOVE OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY LH

    A004TEB

    1. Remove the bolt.

    2. Detach the guide and outer belt anchor bracket sub-assembly LH.